From: National Research Council Canada
This document provides a summary of the minimum requirements imposed by the Canadian Construction Materials Centre (CCMC) for all evaluations based on the below criteria document. Additional requirements may be imposed by the CCMC when necessary for a particular evaluation, and are detailed in the individual evaluation.
Criteria document
Number | CSA O112.9-10 |
Title | Evaluation of Adhesives for Structural Wood Products (Exterior Exposure) |
Document | Standard |
Publisher | CSA Group |
Scope
Evaluations to this performance-based standard cover "exterior exposure" adhesives. Exterior exposure adhesives are used primarily to bond solid wood to solid wood material in structural wood products such as in laminated lumber, edge-glued lumber, and finger-joined lumber designed for wet or exterior service conditions. Adhesives for exterior use include those subjected to repeated wetting and drying and continuous use under high humidity, but do not include those used in below-ground, ground-contact, and marine uses. This standard is not restricted to a specific type of adhesive.
Material requirements
The evaluation holder must demonstrate that the product meets the following requirements (additional requirements may be imposed by the CCMC when necessary, and are detailed in the individual evaluation):
Property | Unit | Requirement |
---|---|---|
Anti-fungal properties Footnote (1) | – | No indication of the presence of fungal growth |
pH of cured adhesive film | – | 3.0 ≤ pH ≤ 11.0 |
Creep resistance |
mm | Overall creep ≤ 0.05 for any specimen |
mm | Creep at any cross section ≤ 0.25 | |
Creep resistance |
mm | Overall creep ≤ 0.6 for any specimen |
mm | Creep at any cross section ≤ 2.9 |
Property | Unit | Hardwood Requirement | Softwood Requirement |
---|---|---|---|
Dry | MPa | ≥ 19 | ≥ 10 |
After vacuum-pressure | MPa | ≥ 11 | ≥ 5.6 |
After boil-dry-freeze | MPa | ≥ 6.9 | ≥ 3.5 |
Property | Unit | Hardwood Requirement | Softwood Requirement | ||
---|---|---|---|---|---|
_ | Lower quartileTable footnote (1) | MedianTable footnote (2) | Lower quartileTable footnote (1) | MedianTable footnote (2) | |
Percent wood failure (dry) | % | 15 | 60 | 75 | 85 |
Percent wood failure (wet) | % | 55 | 80 | 75 | 85 |
Delamination resistanceTable footnote (3) | % | Hardwood | ≤ 1.6Table footnote (4) | Softwood | ≤ 1Table footnote (4) |
© CSA Group. This information is excerpted from the referenced standard published by CSA Group. The full version of the standard should be referenced, and can be obtained from CSA Group.
Installation requirements
The CCMC requires that evaluation holders provide instructions for the installation of the product(s) that:
- do not contravene the National Building Code of Canada, or any provincial or territorial building codes; and
- meet the requirements of CCMC minimum documentation requirements.
Manufacturing requirements
The CCMC requires that evaluation holders, at a minimum, demonstrate that the associated production process:
- is operated under a documented quality system; and
- meets the minimum requirements of the CCMC minimum documentation requirements.
Labelling requirements
The CCMC requires that evaluation holders ensure that product labels:
- reference the associated CCMC number or mark; and
- meet the requirements of CCMC minimum documentation requirements.
Additionally, the CCMC requires that each container bear a label or marking with the following information:
- manufacturer’s name and lot number;
- product name;
- quantity in the container;
- expiry date after which the material should not be used when stored according to the manufacturer’s instructions; and
- brief instructions as to the storage and care of the material prior to use.
Classification information
Products falling within the scope of this document are commonly classified by:
MasterFormat®
- 06 05 23.02 Wood Adhesives
Published CCMC evaluations
The following products have been evaluated to these requirements by the CCMC:
CCMC number: | Manufacturer: | Product names: |
---|---|---|
13372-L | Hexion Inc. | Cascophen AG-5600 (5600Q to 5635Q) series resins |
13522-L | Hexion Inc. | 4001 series resins |
13533-L | Arclin USA LLC | Arclin 5440 |
13536-L | Akzo Nobel | Adhesive 1263/Hardener 9563 |
14042-L | LRBG Chemicals Inc. | Best-Bond PRF-5103W with RCS-5145 catalyst, Best-Bond PRF-5103 with RCS-5145 catalyst |
14035-L | Franklin Adhesives and Polymers | Advantage EP-950A |
14057-L | Bakelite Chemicals LLC | Resibond GP 500CXX series, Resibond GP 475CXX series |
14082-L | Prefere Resins Finland Oy | Prefere 15J566 |
14103-L | Henkel Corporation | LOCTITE® HB X- Line PURBOND® with LOCTITE® PR-3105 PURBOND® Primer |
13512-L | Bostik Inc. | ISOSET® UX-100/WD3-A322 |
14496-L | Hexion Inc. | Wonderbond™ M-700Y, Wonderbond™ M-650Y, Ecobind™ 6500 |
14430-L | Dural, a division of Multibond Inc. | DuraPro G-3270/G-2959M |
Code references
National Building Code of Canada 2015
Code references | Code provision |
---|---|
Table 9.10.3.1.B | Fire and Sound Resistance of Floors, Ceilings and Roofs |