Search

[CCMC 14053-R] CCMC Canadian code compliance evaluation

From: National Research Council Canada

In most jurisdictions this document is sufficient evidence for approval by Canadian authorities.

Learn more about CCMC recognition Look for the trusted CCMC mark on products to verify compliance.

Compliance opinion

It is the opinion of the Canadian Construction Materials Centre that the evaluated products, when used as a foundation wall drainage material in accordance with the conditions and limitations stated in this evaluation, comply with the following code:

Ontario Building Code 2017

ID Code provision Solution type
09-14-02-01-02-b-009.14.2.1.(2)(b) Foundation Wall DrainageAcceptable

The above opinion(s) is/are based on the evaluation by the CCMC of technical evidence provided by the evaluation holder, and is bound by the stated conditions and limitations. For the benefit of the user, a summary of the technical information that forms the basis of this evaluation has been included.

Product information

Product names

  • Isostud GEO T
  • Powerdrain Plus

Product description

The product is a high-density polyethylene (HDPE), semi-rigid, thermally formed sheet that is smooth on one side and dimpled on the other to provide an air gap between the membrane and the wall surface. The product also has an attached polypropylene geotextile mat on the dimpled side. The overall thickness is 8.66 mm with a sheet thickness of 0.025 mm and a hollow core thickness of 8.02 mm. The product is available in rolled sheets 2.44 m (8 ft.) wide by 15.24 m (50 ft.) long.

To ensure correct application, a range of accessories (such as anchors and moulding strips) is included with the product. Photos of the product and anchor accessory are below.

dimpled membrane product

Figure 1. Side facing soil

 

Anchoring system for the product

Figure 2. Anchor

Manufacturing plant

This evaluation is valid only for products produced at the following plant:

Product namesManufacturing plant
Kearneysville, WV, US
Isostud GEO TProduct evaluated by the CCMC
Powerdrain PlusProduct evaluated by the CCMC

Product evaluated by the CCMC Indicates that the product from this manufacturing facility has been evaluated by the CCMC

  Conditions and limitations

The CCMC’s compliance opinion is bound by this product being used in accordance with the conditions and limitations set out below.

  • The product has been classified as Type 2, Class A based on the evidence provided.
  • The product must be installed in accordance with the manufacturer’s instructions.
  • The product was evaluated for use against cast-in-place and concrete block foundations only.
  • The product is a dimpled membrane drainage product designed to act as a protective layer or a capillary breaking layer against the foundation wall to protect the wall against transient or intermittent water that may come in contact with the surface of the wall.
  • The product has been evaluated for use in vertical applications at depths of 3.7 m below grade. Applications greater than 3.7 m are considered to be outside the scope of this evaluation.
  • The product is only one portion of the total foundation drainage system, which consists of a combination of design and construction processes that use different products. In particular, it must be bent at the footing to guide water past the cold joint to a drainage pipe located outside of the footing at the bottom of the wall. This pipe will drain the water collected by the product toward an outflow (i.e., sewer). The product relies on a foundation wall drainage system that conforms to Subsection 9.14.3., Drainage Tile and Pipe, or to Subsection 9.14.4., Granular Drainage Layer, of Division B of the OBC 2017.
  • The placement and grading of backfill must conform to the requirements of Subsection 9.12.3., Backfill, of Division B of the OBC 2017. It is recommended that an impervious topping off layer of clay or silt material be placed on top of the backfill with a positive slope leading surface water away from the building.
  • The product must be protected from exposure to ultraviolet (UV) radiation from sunlight within a maximum of 30 days of its installation.
  • Class A products, with a geotextile facing the soil, must be backfilled before runoff water hits the geotextile (e.g., during a heavy rainfall) to prevent clogging of the filter by fine particles of the soil carried by the running water.
  • Long-term performance of a drainage system will depend on local conditions such as the soil type, hydrogeology of the site, mineralogy and presence of micro-organisms in the soil (i.e., iron ochre), as well as compatibility of the filter with the soil, among other issues. There should be a proper engineering design for the drainage system.
  • The performance of fixtures used to anchor the product in the wall was evaluated for a single anchor. It is the manufacturer’s responsibility to define the pattern and spacing of anchors, considering the anchor strength as well as site-specific issues such as the type of soil, how it will interact with the product, as well as the backfilling method used.
  • The top of the membrane and all vertical joints and terminations must be mechanically fastened and sealed to prevent soil particles from entering behind the membrane. Accessories used to anchor the product are part of the evaluation.
  • The product must be labelled with the manufacturer’s name or logo and the phrase “CCMC 14053-R.”

  Technical information

This evaluation is based on demonstrated conformance with the following criteria:

Evaluation requirements
Criteria number Criteria name
CCMC-TG-334623.01-17CCMC Technical Guide for Foundation Wall Drainage Systems – Dimpled Membranes

The evaluation holder has submitted technical documentation for the CCMC evaluation. Testing was conducted at laboratories recognized by the CCMC. The corresponding technical evidence for this product is summarized below.

Table 1. Results of testing the performance requirements of the product
Property Unit Requirement Result
Compressive strength  initial kPa 150 324.1
Dynamic impact resistance mean failure energy J ≥ 2.45 11.6
Creep resistance residual thickness at 25 years/10°C % ≥ 50% at 25 years/10°C 86.8
Cold bending at –30°C N/A No visible crack No visible crack
Tensile strength at yield kN/m ≥ 8  MDTable footnote (1) 15.8. XD 15.8
Tensile strength elongation at break % ≥ 25 XD 45.2
Tensile strength anisotropy ratio   ≥ 0.5 1.01
Heat agingTable footnote (2) for 2 weeks dimensional change % ≤ 1 MD –0.6, XD –0.6
Heat aging for 2 weeks weight change % ≤ –0.1 –0.7Table footnote (2)
Heat aging for 2 weeks residual compression strength % ≥ 80 of initial 104
Heat aging creep resistance (residual thickness at 25 years/10°C) % ≥ 40% at 25 years/10°C 86
Resistance to alkaline environment appearance N/A No visible crack No visible crack
Resistance to alkaline environment residual compression strength % ≥ 80% of initial 107.0
Resistance to alkaline environment bending at room temperature N/A No visible crack No visible crack
Geotextile fabric properties grab tensile N ≥ 500 MD 522.5, XD 643.8
Geotextile fabric properties puncture resistance N ≥ 100 197.4
Geotextile fabric properties trapezoid tear resistance N ≥ 180 MD 204.9, XD 255.9
Geotextile fabric properties filtration opening size by hydrodynamic sieving µm ≤ 180; Report value 146
Geotextile fabric properties permittivity s-1 ≥ 0.5; Report value 0.95
Geotextile fabric properties UV resistance (retained strength) % retained > 50% after 500 hours MD 83.0, XD 74.2
Hydraulic transmissivity flow rate m3/h∙m 1.33 3.15
Anchorage performance anchorage efficiency kN/anchor Report value 0.478
Geometrical properties
Orientation of the dimples Report value Diagonal
Number of dimples per unit area dimples/m2 Report value 1 526
Overall thickness mm Report value 7.9
Sheet thickness mm Report value 0.77
Hollow core thickness mm Report value 7.13

Administrative information

Use of Canadian Construction Materials Centre (CCMC) assessments

This assessment must be read in the context of the entire CCMC Registry of Product Assessments, any applicable building code or by-law requirements, and/or any other regulatory requirements (for example, the Canada Consumer Product Safety Act, the Canadian Environmental Protection Act, etc.).

It is the responsibility of the user to confirm that the assessment they are using is current and has not been withdrawn or superseded by a later version on the CCMC Registry of Product Assessments.

Disclaimer

The National Research Council of Canada (NRC) has evaluated only the characteristics of the specific product described herein. The information and opinions in this evaluation are directed to those who have the appropriate degree of experience to use and apply its contents (such as authorities having jurisdiction, design professionals and specifiers). This evaluation is valid when the product is used as part of permitted construction, respecting all conditions and limitations stated in the evaluation, and in accordance with applicable building codes and by-laws.

This evaluation is provided without representation, warranty or guarantee of any kind, expressed or implied, and the NRC provides no endorsement for any evaluated product. The NRC accepts no responsibility whatsoever arising in any way from any and all use of or reliance on the information contained herein or the use of any evaluated product. The NRC is not undertaking to render professional or other services on behalf of any person or entity nor to perform any duty owed by any person or entity to another person or entity.

Language

Une version française de ce document est disponible.
In the case of any discrepancy between the English and French version of this document, the English version shall prevail.

Copyright

© His Majesty the King in Right of Canada, as represented by the National Research Council of Canada, 2024

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of the CCMC.

Date modified: