Language selection

Search


[CCMC 14044-R] CCMC Canadian code compliance evaluation

In most jurisdictions this document is sufficient evidence for approval by Canadian authorities.

Learn more about CCMC recognition Look for the trusted CCMC mark on products to verify compliance.

Compliance opinion

It is the opinion of the Canadian Construction Materials Centre that the evaluated product, when used as thermal insulation in accordance with the conditions and limitations stated in this evaluation, complies with the following codes:

National Building Code of Canada 2015

ID Code provision Solution type
09-25-02-02-00-0-009.25.2.2. Insulation MaterialsAcceptable

National Building Code of Canada 2020

ID Code provision Solution type
92502020000009.25.2.2. Insulation MaterialsAcceptable

The above opinion(s) is/are based on the evaluation by the CCMC of technical evidence provided by the evaluation holder, and is bound by the stated conditions and limitations. For the benefit of the user, a summary of the technical information that forms the basis of this evaluation has been included.

Product information

Product name

Amvic Silverboard XS 0.7 pcf

Product description

The product is a low density (nominally 11 kg/m 3) board type expanded polystyrene (EPS) foamed plastic insulation material intended for above-grade, wall cavity applications, with a reflective, perforated, laminated foil facer on both sides.

Manufacturing plants

This evaluation is limited to products produced at the following plants:

Product nameManufacturing plants
Calgary, AB, CAScarborough, ON, CA
Amvic Silverboard XS 0.7 pcfProduct evaluated by the CCMCProduct evaluated by the CCMC

Product evaluated by the CCMC Indicates that the product from this manufacturing facility has been evaluated by the CCMC

  Conditions and limitations

The CCMC’s compliance opinion is bound by this product being used in accordance with the conditions and limitations set out below.

  • The evaluation of this product was limited to above-grade wall cavity insulation for Part 9 construction.
  • Due to the decreased density of this product (compared with CAN/ULC-S701 compliant EPS), it may only be used as an above-grade wall cavity insulation material where the material is not intended to resist compressive stress (i.e., not intended for use as a sheathing material or below grade exterior applications).
  • The material must be installed according to the manufacturer’s installation instructions and must be mechanically fastened to a substructure by cap screws.
  • The product must be clearly identified on the product label as an above-grade wall cavity insulation only, and bear the CCMC number referenced above.

  Technical information

This evaluation is based on demonstrated conformance with the following criteria:

Evaluation requirements
Criteria number Criteria name
CCMC-TG-072113.30-15CCMC Technical Guide for Low Density EPS Board Insulation for Above-Grade Walls
CCMC-TG-072113.30-20CCMC Technical Guide for Low Density EPS Board Insulation for Above-Grade Walls
Material requirements
Table 1. Density test results for the product
Property Unit Requirement Result
Density (bare foam) kg/m3 11.2 ± 1.5 11.2
Performance requirements
Table 2. Performance test results for the product
Property Unit Requirement Result
Thermal resistance (for 25 mm thickness) (m2·°C)/W ≥ 0.65 0.78
Water vapour permeance (for 25 mm thickness) ng/(Pa·s·m2) ≤ 300 44
Dimensional stability Lin.% ≤ 1.5 -0.2
Flexural strength kPa ≥ 170 180
Water absorption Vol.%  ≤ 6.0 0.2
Compressive strength kPa Report value 49.8
Limiting oxygen index % ≥ 24 24
Other technical evidence
Additional performance data requested by the evaluation holder
Table 3. Test results for fire protection requirementsTable footnote footnote (1)
Property Unit Requirement Result
Surface flame-spread - Report value 155
Smoke-development rating - Report value 340

Administrative information

Use of Canadian Construction Materials Centre (CCMC) assessments

This assessment must be read in the context of the entire CCMC Registry of Product Assessments, any applicable building code or by-law requirements, and/or any other regulatory requirements (for example, the Canada Consumer Product Safety Act, the Canadian Environmental Protection Act, etc.).

It is the responsibility of the user to confirm that the assessment they are using is current and has not been withdrawn or superseded by a later version on the CCMC Registry of Product Assessments.

Disclaimer

The National Research Council of Canada (NRC) has evaluated only the characteristics of the specific product described herein. The information and opinions in this evaluation are directed to those who have the appropriate degree of experience to use and apply its contents (such as authorities having jurisdiction, design professionals and specifiers). This evaluation is valid when the product is used as part of permitted construction, respecting all conditions and limitations stated in the evaluation, and in accordance with applicable building codes and by-laws.

This evaluation is provided without representation, warranty or guarantee of any kind, expressed or implied, and the NRC provides no endorsement for any evaluated product. The NRC accepts no responsibility whatsoever arising in any way from any and all use of or reliance on the information contained herein or the use of any evaluated product. The NRC is not undertaking to render professional or other services on behalf of any person or entity nor to perform any duty owed by any person or entity to another person or entity.

Language

Une version française de ce document est disponible.
In the case of any discrepancy between the English and French version of this document, the English version shall prevail.

Copyright

© His Majesty the King in Right of Canada, as represented by the National Research Council of Canada, 2024

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of the CCMC.

Page details

From: National Research Council Canada

Date modified: