[CCMC 13697-L] CCMC Standard compliance evaluation

From: National Research Council Canada

In most jurisdictions this document is sufficient evidence for approval by Canadian authorities.

Learn more about CCMC recognition

  Product information

Product name

Insulthane® Extreme ccSPF

Product description

Ozone-depleting Substances and Halocarbon Alternatives Regulations (ODSHAR)

The evaluation holder attests that this/these product(s) contains a foaming agent that is compliant with the Ozone-depleting Substances and Halocarbon Alternatives Regulations, which is administrated by Environment and Climate Change Canada (ECCC)

The product is a closed-cell, spray-applied rigid polyurethane foam of medium density. The foam system consists of two components that must be labelled as follows along with "CCMC 13697-L":

  • Isocyanate (Component A): Insulthane® Extreme ccSPF isocyanate; and
  • Resin (Component B): Insulthane® Extreme ccSPF.

The two components are mixed on-site by an Elastochem Specialty Chemicals Inc.-qualified installer with fixed-ratio positive displacement equipment. The colour of the installed final cured product is burnt sienna.

Manufacturing plants

This evaluation is limited to products produced at the following plant(s):

  • Brantford, Ontario, Canada

  Technical information

This evaluation is based on demonstrated conformance with the following criteria:

Evaluation requirements
Criteria number Criteria name
CAN/ULC-S705.1-01, Amendment: 1 & 2, Type: 2Standard for Thermal Insulation – Spray Applied Rigid Polyurethane Foam, Medium Density – Material Specification
CAN/ULC-S705.1-15Standard for Thermal Insulation - Spray Applied Rigid Polyurethane Foam, Medium Density - Material Specification

Design values

The product’s classification, minimum site density, long-term thermal resistance (LTTR), water vapour permeance (WVP) and time-to-occupancy values are provided in the tables below:

Conformance with CAN/ULC-S705.1-01, including Amendments 1 and 2
Classification, site density, LTTR, WVP and time-to-occupancy specifications for the product
Product Classification Minimum site densityTable footnote (1)(kg/m3) [lb/ft.3] 50 mm Design LTTR (m2∙°C/W) 50 mm WVPTable footnote (2)(ng/(Pa∙s∙m2)) Time-to-occupancyTable footnote (3)(hours)
Insulthane Extreme Type 2 36.0 [2.2] 2.10 23 25
Conformance with CAN/ULC-S705.1-15
Site density, LTTR, WVP and time-to-occupancy specifications for the product
Product Minimum site densityTable footnote (1)(kg/m3) [lb/ft.3] 50 mm Design LTTR (m2∙°C/W) 50 mm WVPTable footnote (2)(ng/(Pa∙s∙m2)) Time-to-occupancyTable footnote (3)(hours)
Insulthane Extreme 34.5 [2.2] 1.92 39 25
   

Qualified installers

This is a site-manufactured product whereby Elastochem Specialty Chemicals Inc. requires that only specific qualified installers be authorized to install their proprietary spray-applied polyurethane insulation in buildings. In accordance with Elastochem Specialty Chemicals Inc.'s site quality assurance program (SQAP), the certification organization Urethane Foam Consultants (UFC) has been commissioned to license the specified installers and issue them the requisite UFC identification card. All specified installers must have a UFC identification card.

Third-party field auditing of qualified installers

Elastochem Specialty Chemicals Inc., as part of their SQAP, also stipulates site audit inspections be conducted by site inspectors licensed by UFC. Upon completion of the site audit of the specified installers, UFC will report the product’s conformity results and any corrective action required, if necessary, to Elastochem Specialty Chemicals Inc. Building officials who would like site-audit inspections to be conducted on specific building sites can contact UFC at:

Urethane Foam Consultants
160 Main St. S., Suite 547, Brampton, ON L6W 4C1 
Tel.: 905-702-2555 
Fax: 905-456-9439
Website: foamexperts.ca

Administrative information

Disclaimer

This evaluation is issued by the Canadian Construction Materials Centre (CCMC), part of the Construction Research Centre at the National Research Council of Canada (NRC). The evaluation must be read in the context of the entire CCMC Registry of Product Assessments and the legislated applicable building code in effect.

The CCMC was established in 1988 on behalf of the applicable regulator (i.e., the provinces and territories) to ensure—through assessment—conformity of alternative and acceptable solutions to regional building codes as determined by the local authority having jurisdiction (AHJ) as part of the issuance of a building permit.

It is the responsibility of the local AHJs, design professionals, and specifiers to confirm that the evaluation is current and has not been withdrawn or superseded by a later issue. Please refer to the website or contact:

Canadian Construction Materials Centre
Construction Research Centre
National Research Council of Canada
1200 Montreal Road
Ottawa, Ontario, K1A 0R6
Telephone: 613-993-6189
Fax: 613-952-0268

The NRC has evaluated the material, product, system or service described herein only for those characteristics stated herein. The information and opinions in this evaluation are directed to those who have the appropriate degree of experience to use and apply its contents (i.e., AHJs, design professionals and specifiers). This evaluation is only valid when the product is installed in strict compliance with the stated conditions and limitations of evaluation and the applicable local building code. In circumstances where no applicable local building permit is issued and that no confirmation of compliance ‘for use in the intended field application’ is undertaken, this evaluation is null and void in all respects. This evaluation is provided without representation, warranty, or guarantee of any kind, expressed, or implied, and the NRC provides no endorsement for any evaluated material, product, system or service described herein. The NRC accepts no responsibility whatsoever arising in any way from any and all use and reliance on the information contained in this evaluation with respect to its compliance to the referenced code(s) and standard(s). The NRC is not undertaking to render professional or other services on behalf of any person or entity nor to perform any duty owed by any person or entity to another person or entity.

Language

Une version française de ce document est disponible.
In the case of any discrepancy between the English and French version of this document, the English version shall prevail.

Copyright

© 2021 Her Majesty the Queen in Right of Canada, as represented by the National Research Council of Canada.

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of the CCMC.

Date modified: