[CCMC 13657-R] CCMC Canadian code compliance evaluation

From: National Research Council Canada

CCMC number:

13657-R

Status:

Active

Issue date:

2015-04-13

Modified date:

2023-03-28

Evaluation holder:

JDR Enterprises Inc.

292 South Main Street, Suite 200
Alpharetta GA 30009
United States
Telephone: 800-843-7569

Product name:

J-DRain Wrap (Dampproofing)

Code compliance:

NBC 2010

Evaluation requirements:

CCMC-TG-071119.01-10 "CCMC Technical Guide for Foundation Wall Dampproofing Systems – Dimpled Membranes"

In most jurisdictions this document is sufficient evidence for approval by Canadian authorities.

Learn more about CCMC recognition Look for the trusted CCMC mark on products to verify compliance.

Code compliance opinion

It is the opinion of the Canadian Construction Materials Centre that the evaluated product, when used as dampproofing for basement walls in accordance with the conditions and limitations stated in this evaluation, complies with the following code:

National Building Code of Canada 2010

ID	Code provision	Solution type
09-13-02-02-00-0-00	9.13.2.2.(1) Except as otherwise specified in this Se ...	Alternative

The above opinion is based on the evaluation by the CCMC of technical evidence provided by the evaluation holder, and is bound by the stated conditions and limitations. For the benefit of the user, a summary of the technical information that forms the basis of this evaluation has been included.

Product information

Product name

J-DRain Wrap (Dampproofing)

Product description

The product is an extruded high-density polyethylene drainage core bonded with a non-woven filter fabric. The dimples are approximately 7.87 mm high and are intended to provide an air gap between the wall and the adjacent soil. The product is 7.9 mm thick, available in rolls that weigh 17 kg, 27 kg and 34 kg, in widths of 1.22 m, 1.83 m and 2.4 m, respectively. The length of the rolls is 19.81 m.

The figure below illustrates generic installation details for the product.

Installation of the J-DRain Wrap onto a concrete foundation. — Figure 1. Installation of J-DRain Wrap (Dampproofing)

Drainage tile

Membrane

Concrete foundation

Membrane overlap

Mechanically fastened and sealed at top edge and all laps

Manufacturing plant

This evaluation is valid only for products produced at the following plant:

Product name	Manufacturing plant
Product name	Madison, GA, US
J-DRain Wrap (Dampproofing)	Product evaluated by the CCMC

Product evaluated by the CCMC Indicates that the product from this manufacturing facility has been evaluated by the CCMC

Conditions and limitations

The CCMC’s compliance opinion is bound by this product being used in accordance with the conditions and limitations set out below.

The product was evaluated for use against cast-in-place and concrete block foundations only.
The product must be used in locations where the foundation wall is well drained in accordance with Subsection 9.14.2., Foundation Drainage, of Division B of the NBC 2010.
The product must be installed in accordance with the manufacturer’s instructions and be protected from exposure to ultraviolet radiation from the sun within 30 days of installation.
The product is evaluated for use in depths up to 3.7 m below grade. Application depths greater than 3.7 m are considered to be outside the scope of this evaluation.
The product must cover the foundation wall from the top of the footing to the final grade.
The top of the membrane and all vertical joints and terminations must be mechanically fastened and sealed to prevent soil particles from entering behind the membrane.
As the dampproofing membrane does not have to adhere to the surface and can permanently bridge any normal joint, tie hole, fault or shrinkage crack, the wall surface does not have to be parged, cleaned, patched or sealed before hanging the membrane.
The product label and/or packaging must be clearly identified with the following:
- the manufacturer’s name or logo, and
- the phrase “CCMC 13657-R”.

Technical information

This evaluation is based on demonstrated conformance with the following criteria:

Evaluation requirements
Criteria number	Criteria name
CCMC-TG-071119.01-10	CCMC Technical Guide for Foundation Wall Dampproofing Systems – Dimpled Membranes

The evaluation holder has submitted technical documentation for the CCMC’s evaluation. Testing was conducted at laboratories recognized by the CCMC. The corresponding technical evidence for this product is summarized below.

Performance requirements

Table 1. Results of testing of performance properties of J-DRain Wrap (Dampproofing)
Property			Requirement	Result
Thickness of flat area (mm)			Report	0.71
Thickness of dimpled area (mm)			Report	0.91
Weight (g/m²)			≥ 500	736
Dynamic impact			Rating of 3	3
Static puncture			Rating of 3	3
Cold bending at −30°C			No visible cracking	Pass
Water vapour permeance (ng/Pa·s·m²)			≤ 37.2	3.92
Original tensile strength at yield (kN/m)			≥ 8	MD 10.6, XD 8.41^{Table footnote (1)}
Original elongation at break (%)			≥ 25	MD 50.8, XD 30
Water immersion	tensile strength at yield (%)		≥ 80 of original	MD 106.6, XD 114.3
Water immersion	elongation at break (%)		≥ 70 of original	MD 113, XD 113.7
Heat aging	dimensional change (%)		≤ ±1	MD −0.5, XD −0.4
	weight change (%)		≤ ±0.10	−0.3^{Table footnote (2)}
	tensile strength at yield (%)		≥ 80 of original	MD 113.2, XD 103.6
	elongation at break (%)		≥ 70 or original	MD 106.9, XD 101.0
Chemical attack exposure	ammonium chloride	tensile strength at yield (%)	≥ 80 of original	MD 107.5, XD 146.4
	ammonium chloride	elongation at break (%)	≥ 70 of original	MD 109.6, XD 129.7
	sodium sulfate	tensile strength at yield (%)	≥ 80 of original	MD 116, XD 106
	sodium sulfate	elongation at break (%)	≥ 70 of original	MD 98.6, XD 109.3
Compressive strength (kN/m²)			≥ 100	960

Administrative information

Use of Canadian Construction Materials Centre (CCMC) assessments

This assessment must be read in the context of the entire CCMC Registry of Product Assessments, any applicable building code or by-law requirements, and/or any other regulatory requirements (for example, the Canada Consumer Product Safety Act, the Canadian Environmental Protection Act, etc.).

It is the responsibility of the user to confirm that the assessment they are using is current and has not been withdrawn or superseded by a later version on the CCMC Registry of Product Assessments.

Disclaimer

The National Research Council of Canada (NRC) has evaluated only the characteristics of the specific product described herein. The information and opinions in this evaluation are directed to those who have the appropriate degree of experience to use and apply its contents (such as authorities having jurisdiction, design professionals and specifiers). This evaluation is valid when the product is used as part of permitted construction, respecting all conditions and limitations stated in the evaluation, and in accordance with applicable building codes and by-laws.

This evaluation is provided without representation, warranty or guarantee of any kind, expressed or implied, and the NRC provides no endorsement for any evaluated product. The NRC accepts no responsibility whatsoever arising in any way from any and all use of or reliance on the information contained herein or the use of any evaluated product. The NRC is not undertaking to render professional or other services on behalf of any person or entity nor to perform any duty owed by any person or entity to another person or entity.

Language

Une version française de ce document est disponible.
In the case of any discrepancy between the English and French version of this document, the English version shall prevail.

Copyright

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of the CCMC.

Code Compliance via Alternative Solutions

Where a design differs from the acceptable solutions in Division B, then it should be treated as an "alternative solution." A proponent of an alternative solution must demonstrate that the alternative solution addresses the same issues as the applicable acceptable solutions in Division B and their attributed objectives and functional statements. However, because the objectives and functional statements are entirely qualitative, demonstrating compliance with them in isolation is not possible. Therefore, Clause 1.2.1.1.(1)(b) identifies the principle that Division B establishes the quantitative performance targets that alternative solutions must meet. In many cases, these targets are not defined very precisely by the acceptable solutions [...] Nevertheless, Clause 1.2.1.1.(1)(b) makes it clear that an effort must be made to demonstrate that an alternative solution will perform as well as a design that would satisfy the applicable acceptable solutions in Division B—not “well enough” but “as well as.”

National Building Code of Canada, Sentence A-1.2.1.1.(1)(b)

The CCMC has determined that compliance with this provision of the Code has been demonstrated as an Alternative Solution. The evaluation report provides a summary of the basis of CCMC's compliance opinion.

CCMC's code compliance opinions

All CCMC evaluation reports are opinions of code compliance established in accordance with the National Building Code of Canada, Subsection 1.2.1. "Compliance with this Code," which requires compliance to be achieved by:

complying with the applicable acceptable solutions in Division B, or
using an alternative solution that will achieve at least the minimum level of performance required by Division B in the areas defined by the objective and functional statements attributed to the applicable acceptable solutions.

The CCMC assesses compliance with Canadian building, energy and safety codes, and is trusted by over 6,000 regulators across Canada.

Report a problem on this page

Date modified:: 2023-03-28