[CCMC 13606-R] CCMC Canadian code compliance evaluation

From: National Research Council Canada

In most jurisdictions this document is sufficient evidence for approval by Canadian authorities.

Learn more about CCMC recognition Look for the trusted CCMC mark on products to verify compliance.

Code compliance opinion

It is the opinion of the Canadian Construction Materials Centre that the evaluated product, when used as a waterproof membrane covering for decks and balconies subject to light pedestrian traffic in accordance with the conditions and limitations stated in this evaluation, complies with the following code:

National Building Code of Canada 2015

ID Code provision Solution type
09-26-01-02-00-0-009.26.1.2.(1) Roofs shall be protected with roofing, i ...Acceptable
09-26-02-00-00-0-009.26.2. Roofing MaterialsAlternative

Ontario Building Code

Ruling No. 14-209-305 (13606-R) authorizing the use of this product in Ontario, subject to the terms and conditions contained in the Ruling, was made by the Minister of Municipal Affairs and Housing on 2014-09-25 (revised 2017-03-31) pursuant to s.29 of the Building Code Act, 1992 (see Ruling for terms and conditions). This Ruling is subject to periodic revisions and updates.


The above opinion is based on the evaluation by the CCMC of technical evidence provided by the evaluation holder, and is bound by the stated conditions and limitations. For the benefit of the user, a summary of the technical information that forms the basis of this evaluation has been included.

Product information

Product name

Weatherdek Plus

Product description

The product is a polyvinyl chloride (PVC) membrane with a non-woven polyester backing. The nominal thickness is 1.5 mm. The surface of the product is embossed to provide a textured finish. The membrane is available in rolls that are 1 372 mm or 1 829 mm wide and can be cut to a required length. The product is available in a variety of colours.

Manufacturing plant

This evaluation is valid only for products produced at the following plant:

Product nameManufacturing plant
Winchester, VA, US
Weatherdek PlusProduct evaluated by the CCMC

Product evaluated by the CCMC Indicates that the product from this manufacturing facility has been evaluated by the CCMC

  Conditions and limitations

The CCMC’s compliance opinion is bound by this product being used in accordance with the conditions and limitations set out below.

  • The product can be used as a membrane that is fully adhered to a continuous solid substrate, such as a plywood or concrete deck and balconies that are subject to light pedestrian traffic.
  • The product must be used only in conjunction with plywood or concrete substrates. The membrane must be fully adhered to the substrate with adhesives WD-1000 (on concrete or plywood substrates) or WD-7633 (on plywood substrates only) and applied as per the installation manual.
  • The product is limited for use in areas that are subject to traffic loads generated by residential occupancies only.
  • The product must not be exposed to chemical attack or spillage. In situations where extended contact with chemicals or pollutants may occur, the suitability of the product must be determined.
  • Any physical or chemical damage to the membrane must be repaired in accordance with the manufacturer’s instructions. The product must not be installed with butt seam joints.
  • The product is limited for use where the roof or deck surface has a minimum slope of 1:48.
  • Joints must be shingle-lapped in order to shed water.
  • The product must be installed by approved applicators only and in strict conformance with the manufacturer’s installation instructions.
  • The product or its packaging must be identified with the manufacturer’s name or logo and the phrase “CCMC 13606-R.”

  Technical information

This evaluation is based on demonstrated conformance with the following criteria:

Evaluation requirements
Criteria number Criteria name
CCMC-TG-075419.01-15CCMC Technical Guide for “PVC Sheet-Applied Decking membranes (Exposed to light Pedestrian Traffic)”
Physical property requirements
Table 1. Results of physical property testing of the product
Property Unit Requirement Results
Dimensional tolerance (length) % Tolerance shall be within 0% and + 3% of reported length 0.3
Dimensional tolerance (width) % Tolerance shall be within 0% and + 3% of reported width 0
Overall thickness of the PVC membrane mm ≥ 1.2 ± 10% of thickness 1.3
Mechanical property requirements
Table 2. Results of mechanical property testing of the product
Property Unit Requirement Results
Breaking strength N ≥ 245 514
Elongation, as received MDTable footnote (1) % ≥ 25 250
CMDTable footnote (2) % ≥ 25 258
Elongation, with backing removed MDTable footnote (1) % ≥ 250 272
CMDTable footnote (2) % ≥ 250 265
Tear resistance N ≥ 45 79
Static puncture kg ≥ 15 15
Dynamic puncture J ≥ 20 20
Low temperature impact No cracks at –30°C No cracks
Low temperature flexibility No cracks at –40°C No cracks
Dimensional changes MDTable footnote (1) % ≤ 2.0 0.5
CMDTable footnote (2) % ≤ 2.0 0.1
Abrasion resistance Cycles ≥ 5 000 5 000
Slip resistance DCOFTable footnote (3) ≥ 0.42 0.80
Fungi resistance Sustained growth No growth No growth
Discoloration No discoloration No discoloration
Fabric adhesion to membrane kN/m ≥ 0.525 0.557
Crack bridging  No cracking, splitting or pinholes No cracking, splitting or pinholes
Adhesion to plywood With adhesive WD-1000 KPa Report value 50.5
With adhesive WD-7633 KPa Report value 51.9
Adhesion to concrete With adhesive WD-1000 KPa Report value ≥ 56.7Table footnote (4)
Water resistance Weight change % ≤ 3 1.62
Retained breaking strength % ≥ 90 96
Retained elongation % ≥ 90 96
Heat aging Visiual inspection No cracking, crazing or blistering No cracking, crazing or blistering
Weight change % ≤ 5 –0.69
Retained breaking strength % ≥ 90 97
Retained elongation % ≥ 90 97
Low temperature impact Report value No cracks at –30°C
Abrasion resistance Cycles ≥ 1 500 4 000
Slip resistance DCOFTable footnote (3) ≥ 0.42 0.779
Fungi resistance No growth or discoloration No growth or discoloration
Falling weight impact resistance J Report value 9.8
Accelerated weathering Visual inspection No cracking, crazing or blistering No cracking, crazing or blistering
Retained breaking strength % ≥ 80 88
Retained elongation % ≥ 80 81
Low temperature flexibility Report value No cracks at –25°C
Abrasion resistance Cycles ≥ 1 500 4 000
Slip resistance DCOFTable footnote (3) ≥ 0.42 0.814
Seam strength Reference (no seam) N Report value 451
Unconditioned % ≥ 75 91
After heat aging % ≥ 70 92
After 7 days in boiling water % ≥ 70 80

Administrative information

Disclaimer

This evaluation is issued by the Canadian Construction Materials Centre (CCMC), a part of the Construction Research Centre at the National Research Council of Canada (NRC). The evaluation must be read in the context of the entire CCMC Registry of Product Assessments and the legislated applicable building code in effect.

The CCMC was established in 1988 on behalf of the applicable regulator (i.e., the provinces and territories) to ensure—through assessment—conformity of alternative and acceptable solutions to regional building codes as determined by the local authority having jurisdiction (AHJ) as part of the issuance of a building permit.

It is the responsibility of the local AHJs, design professionals, and specifiers to confirm that the evaluation is current and has not been withdrawn or superseded by a later issue. Please refer to the website or contact:

Canadian Construction Materials Centre
Construction Research Centre
National Research Council of Canada
1200 Montreal Road
Ottawa, Ontario, K1A 0R6
Telephone: 613-993-6189
Fax: 613-952-0268

The NRC has evaluated the material, product, system or service described herein only for those characteristics stated herein. The information and opinions in this evaluation are directed to those who have the appropriate degree of experience to use and apply its contents (i.e., AHJs, design professionals and specifiers). This evaluation is only valid when the product is installed in strict compliance with the stated conditions and limitations of evaluation and the applicable local building code. In circumstances where no applicable local building permit is issued and that no confirmation of compliance ‘for use in the intended field application’ is undertaken, this evaluation is null and void in all respects. This evaluation is provided without representation, warranty, or guarantee of any kind, expressed, or implied, and the NRC provides no endorsement for any evaluated material, product, system or service described herein. The NRC accepts no responsibility whatsoever arising in any way from any and all use and reliance on the information contained in this evaluation with respect to its compliance to the referenced code(s) and standard(s). The NRC is not undertaking to render professional or other services on behalf of any person or entity nor to perform any duty owed by any person or entity to another person or entity.

Language

Une version française de ce document est disponible.
In the case of any discrepancy between the English and French version of this document, the English version shall prevail.

Copyright

© His Majesty the King in Right of Canada, as represented by the National Research Council of Canada, 2022

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of the CCMC.

Date modified: