[CCMC 12788-R] CCMC Canadian code compliance evaluation
From: National Research Council Canada
Dörken Systems Inc.
4655 Delta Way
|Code compliance:||OBC 2017|
In most jurisdictions this document is sufficient evidence for approval by Canadian authorities.Learn more about CCMC recognition Look for the trusted CCMC mark on products to verify compliance.
Code compliance opinion
It is the opinion of the Canadian Construction Materials Centre that the evaluated product, when used as a foundation wall drainage material in accordance with the conditions and limitations stated in this evaluation, complies with the following code:
Ontario Building Code 2017
|ID||Code provision||Solution type|
|09-14-02-01-02-b-00||126.96.36.199.(2)(b) Foundation Wall Drainage||Acceptable|
Ruling No. 98-02-52 (12788-R) authorizing the use of this product in Ontario, subject to the terms and conditions contained in the Ruling, was made by the Minister of Municipal Affairs and Housing on 0199-02-17 pursuant to s.29 of the Building Code Act, 1992 (see Ruling for terms and conditions). This Ruling is subject to periodic revisions and updates.
The above opinion is based on the evaluation by the CCMC of technical evidence provided by the evaluation holder, and is bound by the stated conditions and limitations. For the benefit of the user, a summary of the technical information that forms the basis of this evaluation has been included.
The product is a high-density polyethylene, quasi-rigid, plastic sheet membrane that is extruded in a manner that results in a dimpled surface on one side and a smooth surface on the other. The sheets have 8-mm-deep dimples and are available in rolls that are 0.6 mm thick, 20 m long and in widths ranging from 1.07 m to 3.0 m. The dimpled surface is installed facing the foundation wall to provide a capillary breaking layer that protects against transient or intermittent water.
Delta®-MS profiles and anchors are illustrated in Figure 1, Figure 2 and Figure 3.
This evaluation is valid only for products produced at the following plant:
|Product name||Manufacturing plant|
|Beamsville, ON, CA|
|Delta®-MS||Product evaluated by the CCMC|
Product evaluated by the CCMC Indicates that the product from this manufacturing facility has been evaluated by the CCMC
Conditions and limitations
The CCMC’s compliance opinion is bound by this product being used in accordance with the conditions and limitations set out below.
- Based on the evidence provided, the product has been classified as Type 2 (applications up to depths of 3.7 m), Class B (cups facing soil).
- The product must be installed in accordance with the manufacturer’s instructions.
- The product was evaluated for use against cast-in-place concrete and concrete block foundations only.
- The product is a dimpled membrane drainage product designed to act as a protective layer or a capillary breaking layer against the foundation wall to protect the wall against transient or intermittent water that may come in contact with the surface of the wall.
- The product has been evaluated for use in vertical applications in depths of 3.7 m below grade. Applications greater than 3.7 m are considered to be outside the scope of this Evaluation.
- The product is only one portion of the total foundation drainage system, which consists of a combination of design and construction processes that use different products. In particular, the product must be bent at the footing to guide water past the cold joint to a drainage pipe located outside of the footing at the bottom of the wall. This pipe will drain the water collected by the product toward an outflow (i.e., sewer). The product relies on a foundation wall drainage system that conforms to Subsections 9.14.3., Drainage Tile and Pipe, or to Subsection 9.14.4., Granular Drainage Layer, of Division B of the OBC 2017.
- The placement and grading of backfill must conform to the requirements of Subsection 9.12.3., Backfill, of Division B of the OBC 2017. It is recommended that an impervious “topping off” layer of clay or silt material be placed on top of the backfill with a positive slope leading surface water away from the building.
- The product must be protected from exposure to ultraviolet (UV) sunlight within a maximum of 30 days of its installation.
- Long-term performance of a drainage system will depend on local conditions such as the soil type, hydrogeology of the site, mineralogy and presence of microorganisms in the soil (i.e., iron ochre), as well as compatibility of the filter with the soil, among other issues. There should be a proper engineering design for the drainage system.
- The performance of fixtures used to anchor the product in the wall was evaluated for a single anchor. It is the manufacturer’s responsibility to define the pattern and spacing of anchors considering the anchor strength as well as site-specific issues such as the type of soil, how it will interact with the product, and the backfilling method used.
- The top of the membrane and all vertical joints and terminations must be mechanically fastened and sealed to prevent soil particles from entering behind the membrane. Accessories used to anchor the product are part of the Evaluation.
- The product must be labelled with the manufacturer’s name or logo and the phrase “CCMC 12788-R.”
This evaluation is based on demonstrated conformance with the following criteria:
|Criteria number||Criteria name|
|CCMC-TG-334623.01-17||CCMC Technical Guide for Foundation Wall Drainage Systems – Dimpled Membranes|
The Report Holder has submitted technical documentation for the CCMC’s evaluation. Testing was conducted at laboratories recognized by the CCMC. The corresponding technical evidence for this product is summarized below.
|Compressive strength (initial)||kPa||150||223|
|Dynamic impact resistance (mean failure energy)||J||≥ 2.45||8.3|
|Creep resistance (residual thickness at 25 years/10°C)||%||≥ 40% at 25 years/10°C||77.5|
|Cold bending at –30°C||N/A||No visible crack||No visible crack|
|Tensile strength||at yield||kN/m||≥ 8||XDTable footnote (1) 8.1|
|elongation at break||%||≥ 25||XD 29.8|
|Anisotropy ratio||N/A||≥ 0.5||1.1|
|tensile strength in print area||%||≥ 90% of tensile strength||100%|
|Heat aging for 2 weeks||dimensional change||%||≤ 1||MDTable footnote (1) –0.6,
|weight change||%||≤ –0.1||0.0|
|residual compression strength||%||≥ 80 of initial||107.8|
|Resistance to alkaline environment||appearance||N/A||No visible crack||No visible crack|
|residual compression strength||%||≥ 80 of initial||101.5|
|cold bending at –30°C||N/A||No visible crack||No visible crack|
|Orientation of the dimples||–||Report value||Diagonal|
|Number of dimples per unit area||dimples/m2||Report value||1 560|
|Overall thickness||mm||Report value||8.43|
|Sheet thickness||mm||Report value||0.48|
|Hollow core thickness||mm||Report value||7.95|
|Anchorage performance anchorage efficiency||kN/anchor||Report value||0.95|
This evaluation is issued by the Canadian Construction Materials Centre (CCMC), a part of the Construction Research Centre at the National Research Council of Canada (NRC). The evaluation must be read in the context of the entire CCMC Registry of Product Assessments and the legislated applicable building code in effect.
The CCMC was established in 1988 on behalf of the applicable regulator (i.e., the provinces and territories) to ensure—through assessment—conformity of alternative and acceptable solutions to regional building codes as determined by the local authority having jurisdiction (AHJ) as part of the issuance of a building permit.
It is the responsibility of the local AHJs, design professionals, and specifiers to confirm that the evaluation is current and has not been withdrawn or superseded by a later issue. Please refer to the website or contact:
Canadian Construction Materials Centre
Construction Research Centre
National Research Council of Canada
1200 Montreal Road
Ottawa, Ontario, K1A 0R6
The NRC has evaluated the material, product, system or service described herein only for those characteristics stated herein. The information and opinions in this evaluation are directed to those who have the appropriate degree of experience to use and apply its contents (i.e., AHJs, design professionals and specifiers). This evaluation is only valid when the product is installed in strict compliance with the stated conditions and limitations of evaluation and the applicable local building code. In circumstances where no applicable local building permit is issued and that no confirmation of compliance ‘for use in the intended field application’ is undertaken, this evaluation is null and void in all respects. This evaluation is provided without representation, warranty, or guarantee of any kind, expressed, or implied, and the NRC provides no endorsement for any evaluated material, product, system or service described herein. The NRC accepts no responsibility whatsoever arising in any way from any and all use and reliance on the information contained in this evaluation with respect to its compliance to the referenced code(s) and standard(s). The NRC is not undertaking to render professional or other services on behalf of any person or entity nor to perform any duty owed by any person or entity to another person or entity.
Une version française de ce document est disponible.
In the case of any discrepancy between the English and French version of this document, the English version shall prevail.
© His Majesty the King in Right of Canada, as represented by the National Research Council of Canada, 2022
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of the CCMC.