[CCMC 14230-R] CCMC Canadian code compliance evaluation
From: National Research Council Canada
BASF Canada Inc.
10 Constellation Court
|Compliance:||NBC 2015, NBC 2020, OBC|
In most jurisdictions this document is sufficient evidence for approval by Canadian authorities.Learn more about CCMC recognition Look for the trusted CCMC mark on products to verify compliance.
It is the opinion of the Canadian Construction Materials Centre that the evaluated product, when used as thermal insulation in accordance with the conditions and limitations stated in this evaluation, complies with the following codes:
National Building Code of Canada 2015
|ID||Code provision||Solution type|
|05-09-01-01-00-0-00||18.104.22.168. Compliance with Applicable Standards||Alternative|
|09-25-02-02-01-h-00||22.214.171.124.(1)(h) Insulation Materials||Alternative|
|09-25-02-05-00-0-00||126.96.36.199. Installation of Spray-Applied Polyurethane||Alternative|
National Building Code of Canada 2020
|ID||Code provision||Solution type|
|188.8.131.52.||184.108.40.206. Compliance with Applicable Standards||Alternative|
|220.127.116.11.||18.104.22.168. Installation of Spray-Applied Polyurethane||Alternative|
Ontario Building Code
Ruling No. 21-06-369 (14230-R) authorizing the use of this product in Ontario, subject to the terms and conditions contained in the Ruling, was made by the Minister of Municipal Affairs and Housing on 2021-12-13 pursuant to s.29 of the Building Code Act, 1992 (see Ruling for terms and conditions). This Ruling is subject to periodic revisions and updates.
The above opinion(s) is/are based on the evaluation by the CCMC of technical evidence provided by the evaluation holder, and is bound by the stated conditions and limitations. For the benefit of the user, a summary of the technical information that forms the basis of this evaluation has been included.
“WALLTITE® XL01” is a spray-applied, rigid polyurethane foam of medium density that has a closed-cell structure. The foaming system consists of two components that must be labelled with “CCMC 14230-R” and the following information:
- Isocyanate (Component A): “Elastospray® 8000A”; and
- Resin (Component B): “WALLTITE® XL01.”
The two components are mixed on-site by a BASF Canada Inc.-qualified installer (see Section 3.2) with fixed-ratio positive displacement equipment.
This product is referred to as a ‘high-lift’ spray polyurethane foam whereby a thick layer of “WALLTITE® XL01” can be applied in a single pass. The product is installed at a maximum nominal thickness of 127 mm and a minimum nominal thickness of 50 mm. This installation method differs from the method described in CAN/ULC-S705.2-05, “Standard for Thermal Insulation – Spray Applied Rigid Polyurethane Foam, Medium Density – Application,” which specifies a 50-mm maximum nominal thickness for spray foam installed in a single pass.
The final cured product has a density of 32.25 kg/m3 and is available in the following colour:
- Dark purple
At 50-mm thick, the design long-term thermal resistance (LTTR) value is 1.87 (m2·K)/W. See physical properties of the product for estimated LTTR values at higher thicknesses.
The product is available in winter grade and regular grade formulations.
This is a site-manufactured product; it is finished on-site following the spray-application of raw materials produced at the manufacturing plant(s) below.
This evaluation is limited to products produced at the following plants:
|Product name||Manufacturing plants|
|Blackie, AB, CA||Toronto, ON, CA|
|WALLTITE® XL01||Product evaluated by the CCMC||Product evaluated by the CCMC|
Product evaluated by the CCMC Indicates that the product from this manufacturing facility has been evaluated by the CCMC
Conditions and limitations
The CCMC’s compliance opinion is bound by this product being used in accordance with the conditions and limitations set out below.
CCMC’s compliance opinion is bound by “WALLTITE® XL01” being used in accordance with the conditions and limitations set out below.
- The cured polyurethane foam must have a minimum nominal thickness of 50 mm and a maximum nominal thickness of 127 mm. Any product sprayed to a thickness greater than 140 mm (maximum nominal thickness plus a field safety margin of 13 mm) must be removed from the substrate immediately after application and the substrates sprayed again. IMPORTANT: spraying to a thickness greater than 140 mm may result in spontaneous combustion or poor foam quality.
- The application of the foam in multiple passes is beyond the scope of this evaluation.
- The polyurethane foam can be applied on the substrates listed under physical properties of the product. Substrates must be clean, dry, and free of grease, frost, dust, rust and other contaminants that may affect the adhesion performance of the foam to the substrate.
- Below-grade (exterior side of foundation wall) and attic applications are beyond the scope of this evaluation.
- As required in Article 22.214.171.124., Installation of Thermal Insulation, of Division B of the NBC 2010 and NBC 2015, the insulation shall have a reasonably uniform insulation value over the entire face of the insulated area.
- The assessment of the fire hazard-peak temperature reached during foam application is only valid for the tested substrates under material temperature requirements due to exothermic reaction and for foam applied in a single pass with a maximum nominal thickness of 127 mm.
- The peak temperatures of the thick single pass may affect the performance and durability of materials and equipment in contact with the foam (such as ducts and pipes). The performance of such components is beyond the scope of this evaluation. The measured maximum temperature of the foam while curing is specified under material temperature requirements due to exothermic reaction.
- The interior side of the polyurethane foam insulation must be covered with an approved thermal barrier as per:
- Article 126.96.36.199., Protection of Foamed Plastics, of Division B of the NBC 2010 or NBC 2015;
- Article 188.8.131.52., Combustible Insulation and its Protection, of Division B of the NBC 2010;
- Article 184.108.40.206., Foamed Plastic Insulation, of Division B of the NBC 2015; or
- Article 220.127.116.11., Protection of Foamed Plastics, of Division B of the NBC 2010 or NBC 2015.
- When applicable, the exterior surface of an exterior wall containing this insulation shall be designed in accordance with Section 9.10, Fire Protection, of Division B of the NBC 2010 or NBC 2015, or Section 3.2, Building Fire Safety, of Division B of the NBC 2010 or NBC 2015. The product shall not be used in exposed interior or exterior locations.
- The insulation must be kept away at least 75 mm (or as required by building regulations and safety codes) from heat-emitting devices (such as recessed lighting fixtures and chimneys). The insulation shall not be used inside electrical outlets or junction boxes.
- For retrofit construction, the time to occupancy is 25 hours when installed with the requisite ventilation of the segregated retrofit area as per CAN/ULC-S705.2. Additional details are provided in Note 3 in physical properties of the product.
- When the product is installed in an exterior insulation sheathing-type application, the low air and water vapour-permeance value of the product requires that the wall assembly conform to Table 18.104.22.168., Ratio of Outboard to Inboard Thermal Resistance, of Division B of the NBC 2010 or NBC 2015.
- The product must not be installed after the expiry date printed on the label of each container. The product has a shelf life of four (4) months from the date of manufacture.
- The substrate temperatures are −15°C to 5°C for the winter grade formulation and 0°C to 40°C for the regular grade formulation. The appropriate formulation shall be chosen for the specific temperature conditions of application in consultation with BASF Canada Inc.
- The installation of the product must:
- conform to the general requirements of CAN/ULC-S705.2-05,
- comply with the manufacturer’s specific installation instructions for their proprietary high-lift product
- be performed by a qualified installer, and
- meet all conditions and limitations in this evaluation.
- The continuous in-service temperature of the insulation must not exceed the range of −60°C to 80°C. The building envelope in which this product is installed must conform to the requirements of Division B of the NBC 2010 or NBC 2015 for vapour barrier, air barrier and dampproofing (interior below-grade walls).
- The product must be protected from ultraviolet radiation within 90 days of installation.
- The installation must be carried out by certified installers in accordance with the manufacturer's instruction manual, which must be available at the job site at all times during the installation for review by the building official.
- The components, “Elastospray® 8000A” isocyanate and “WALLTITE® XL01” resin, must have their respective containers (i.e., drums) identified by the phrase “CCMC 14230-R.”
This is a site-manufactured product whereby BASF Canada Inc. requires that only specific qualified installers be authorized to install their proprietary spray-applied polyurethane insulation in buildings. In accordance with BASF Canada Inc.’s site quality assurance program (SQAP), the certification organization (CO) Caliber Quality Solutions Inc. (Caliber) has been commissioned to license the specified installers and issue them the requisite Caliber identification card. All specified installers must have a Caliber identification card.
Third-Party Site Auditing of Qualified Installers
As part of their SQAP, BASF Canada Inc. also stipulates that site audit inspections be conducted by site inspectors licensed by Caliber. Upon completion of the site audit, Caliber will report the product’s conformity results and any corrective action required, if necessary, to BASF Canada Inc. Building officials who would like site-audit inspections to be conducted on specific building sites can contact Caliber at:
Caliber Quality Solutions Inc. (Caliber)
120 Eglington Avenue East,
Suite 1000 Toronto, ON M4P 1E2
Web site: www.caliberqa.com
This evaluation is based on demonstrated conformance with the following criteria:
|Criteria number||Criteria name|
|CCMC-TG-072119.06-15||CCMC Technical Guide for Spray-Applied Rigid Polyurethane Foam Insulation – Single Pass Medium Density|
|CCMC-TG-072119.06-20||CCMC Technical Guide for Spray-Applied Rigid Polyurethane Foam Insulation – Single Pass Medium Density|
The Report Holder has submitted technical documentation for CCMC’s evaluation. Testing was conducted at laboratories recognized by CCMC. The corresponding technical evidence for this product is summarized below.
The following were the key performance requirements for the evaluation:
- Material qualification:
- Foam basic properties per CAN/ULC-S705.1 requirements except for the sample preparation. Samples were sprayed at the maximum nominal thickness of 127 mm using a single pass instead of two passes of 30-mm each nominal thickness as specified in CAN/ULC-S705.1. Foam application of regular formulation at 23°C was used for testing as required in CAN/ULC-S705.1.
- Key physical properties in high- and low-temperature applications.
- Adhesion performance: Foam adhesion strength to different substrates (the manufacturer-selected substrates were wood, gypsum, and concrete). Foam application of regular formulation at high surface temperature was considered a worst-case scenario.
- Foam uniformity: Foam cells uniformity when sprayed in different wall cavity dimensions. Foam application of regular formulation at high surface temperature and at maximum nominal thickness was considered a worst-case scenario.
- Fire hazard: Maximum temperature achieved in the foam due to exothermic reaction (high internal temperature generated while curing). Foam application of winter grade formulation at lowest surface temperature was considered a worst-case scenario by the manufacturer.
Physical properties from ambient temperature application
The basic properties of the product’s regular formulation, when sprayed over polyethylene board having a surface temperature of 23°C, are presented below. Test specimens used were extracted from the central area of foam samples sprayed at a nominal 127-mm thickness.
|Air permeance for a 25-mm-thick specimen||L/(s∙m2)||≤ 0.020||0.0022|
|Apparent core density||kg/m3||≥ 28.0||32.25|
|Compressive strength||kPa||≥ 170||232|
|Dimensional stability, without substrate volume change at||−20°C||
|70°C, 97 ± 3% RH||+14||1.6|
|Surface burning characteristics for a 100- mm-thick specimen||Flame-spread ratingTable footnote (1)||--||≤ 500||240|
|Open-cell content volume||%||≤ 10||1.2|
|Initial thermal resistance for a 50-mm-thick specimen (after 13 days at 23°C)||(m2∙K)/W||Declare||2.46|
Long-term thermal resistance (LTTR)Table footnote (2)
|Tensile strength||kPa||≥ 200||425|
|Volatile organic emissions (VOC)Table footnote (3)||hrs||≤ 30 days||25|
|Water absorption by volume||%||≤ 4.0||0.73|
|Water vapour permeance (WVP) for a 50-mm-thick specimen||Specimen with bottom skin intact (top skin removed)||ng/(Pa∙s∙m2)||≤ 60||40|
|Fungi resistance||--||No growth||None|
Physical properties in high-temperature application
The air permeance and water vapour permeance of the product’s regular formulation, when sprayed over polyethylene board having a surface temperature of 40°C, are presented below. Test specimens used were extracted from foam samples sprayed at a nominal 127-mm thickness.
|Air permeance for a 26.2-mm-thick specimen||L/(s∙m2)||≤ 0.020||0.0018|
|Water vapour permeance (WVP) for a 50-mm-thick specimen||specimen with bottom skin intact (top skin removed)||ng/(Pa∙s∙m2)||≤ 60||59|
Physical properties in low-temperature application
The initial and long-term thermal resistance of the product’s winter grade formulation, when sprayed over concrete tiles having a surface temperature of −15°C, are presented below. Test specimens used were extracted from foam samples sprayed at a nominal 60-mm thickness.
|Initial thermal resistance for a 50-mm-thick specimen (after 13 days at 23°C)||(m2∙K)/W||Report value||2.42|
|Long-term thermal resistance (LTTR)Table footnote (1)||125 mm||
The adhesion strength of the product’s regular formulation, when sprayed over wood, gypsum and concrete substrates having a surface temperature of 40°C, is presented in below. Foam samples were sprayed at a nominal 127-mm thickness.
|Adhesion strengthTable footnote (1)||Exterior gypsum board||
The average cell size of the product’s regular formulation, when sprayed in wood frame cavities made of oriented strandboard (OSB) sheathing and 89-mm × 140-mm wood studs spaced at 600 mm on centre (o.c.), 400 mm o.c. and 300 mm o.c., are presented below. The substrate surface temperature was 40°C. Foam sample thicknesses were 125 mm to 135 mm.
|Average cell size||Panel with two cavities of 600 mm o.c.||mm||< 0.5||PassTable footnote (1)|
|Panel with two cavities of 400 mm o.c.||mm||< 0.5||PassTable footnote (2)|
|Panel with two cavities of 300 mm o.c.||mm||< 0.5||PassTable footnote (3)|
Material temperature requirements due to exothermic reaction
The maximum temperature and amount of time required for the product’s winter grade formulation to cool down when sprayed over wood and gypsum substrate with a surface temperature of 5.3°C are presented below. Spraying over concrete substrate was not part of the testing protocol since this type of substrate is a non-combustible material. Foam sample thicknesses were 125 mm to 127 mm.
|Maximum recorded temperature at any place in the foam||OSB substrate||°C
|Temperatures in the foam vs. time||°C||Temperature vs. time must be decreasing after the peakTable footnote (1)||Pass|
|Maximum recorded temperature at wood frame–foam interface||OSB substrate||°C
|Maximum recorded temperature at substrate–foam interface:
||Wood material and gypsum bord||OSB substrate||°C
|Gypsum substrate||< 170||102.2|
||Foam temperature must be less than melting temperature of the materialTable footnote (2)||n/a|
|Non-combustible materials||Not required||n/a|
|Timeframe for the foam temperature to cool down to 21°C -||OSB substrate||hr:min||Report value||06:16Table footnote (3)|
|Gypsum substrate||hr:min||Report value||06:46|
|Effect of maximum recorded temperature on electrical wires||OSB substrateTable footnote (4)||--||No damage to the electrical wire jacket where maximum foam temperature is reached||159°CTable footnote (4) was recorded near the wire, and no visual effect was observed on the wire jacket|
Use of Canadian Construction Materials Centre (CCMC) assessments
This assessment must be read in the context of the entire CCMC Registry of Product Assessments, any applicable building code or by-law requirements, and/or any other regulatory requirements (for example, the Canada Consumer Product Safety Act, the Canadian Environmental Protection Act, etc.).
It is the responsibility of the user to confirm that the assessment they are using is current and has not been withdrawn or superseded by a later version on the CCMC Registry of Product Assessments.
The National Research Council of Canada (NRC) has evaluated only the characteristics of the specific product described herein. The information and opinions in this evaluation are directed to those who have the appropriate degree of experience to use and apply its contents (such as authorities having jurisdiction, design professionals and specifiers). This evaluation is valid when the product is used as part of permitted construction, respecting all conditions and limitations stated in the evaluation, and in accordance with applicable building codes and by-laws.
This evaluation is provided without representation, warranty or guarantee of any kind, expressed or implied, and the NRC provides no endorsement for any evaluated product. The NRC accepts no responsibility whatsoever arising in any way from any and all use of or reliance on the information contained herein or the use of any evaluated product. The NRC is not undertaking to render professional or other services on behalf of any person or entity nor to perform any duty owed by any person or entity to another person or entity.
Une version française de ce document est disponible.
In the case of any discrepancy between the English and French version of this document, the English version shall prevail.
© His Majesty the King in Right of Canada, as represented by the National Research Council of Canada, 2023
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of the CCMC.