[CCMC 14043-R] CCMC Canadian code compliance evaluation
From: National Research Council Canada
In most jurisdictions this document is sufficient evidence for approval by Canadian authorities.Learn more about CCMC recognition Look for the trusted CCMC mark on products to verify compliance.
It is the opinion of the Canadian Construction Materials Centre that the evaluated product, when used as an exterior cladding for buildings of combustible construction in accordance with the conditions and limitations stated in this evaluation, complies with the following code:
National Building Code of Canada 2015
|ID||Code provision||Solution type|
|09-27-02-00-00-0-00||9.27.2. Required Protection from Precipitation||Acceptable|
|09-27-03-00-00-0-00||9.27.3. Second Plane of Protection||Acceptable|
|09-27-12-00-00-0-00||9.27.12. Vinyl Siding||Alternative|
The above opinion(s) is/are based on the evaluation by the CCMC of technical evidence provided by the evaluation holder, and is bound by the stated conditions and limitations. For the benefit of the user, a summary of the technical information that forms the basis of this evaluation has been included.
The products are made of heavy-gauge polyvinyl chloride (PVC) and coated with a PVC film (RENOLIT) designed for exterior applications.
The profiles are tongue and groove and fastened to the building structure through pre-punched nailing slots located along the top edge of the profiles, which are concealed after the upper profile is installed. The products are available in a 150-mm channeled groove profile and a 150-mm V-groove profile. The products are 3 660 mm or 5 790 mm in length.
All accessories are made of aluminum covered with a PVC film (RENOLIT).
This evaluation is valid only for products produced at the following plant:
|Product name||Manufacturing plant|
|Sagiwall||Product evaluated by the CCMC|
Product evaluated by the CCMC Indicates that the product from this manufacturing facility has been evaluated by the CCMC
Conditions and limitations
The CCMC’s compliance opinion is bound by this product being used in accordance with the conditions and limitations set out below.
- The products are limited to use as exterior siding for the buildings falling within the scope of Part 9, Housing and Small Buildings, of Division B of the NBC 2015.
- When installed, all the building elements relevant to the product must comply with the requirements of the NBC 2015.
- The siding panels must be installed on furring providing a second plane of protection that consists of a continuous, clear, uninterrupted vented air space of 10 mm outboard of the sheathing membrane.
- The furring must be installed over the sheathing membrane.
- The system requires flashing at appropriate locations in order to drain water to the outside.
- Furring for the attachment of the cladding must not be less than 19 mm × 38 mm, securely nailed to the sheathing or framing, and spaced not more than 600 mm on centre (o.c.).
- The products shall be installed in accordance with the manufacturer’s current installation instructions:
- “Sagiwall Installation Guidelines” November 1, 2020, Version 1.1
- If there is any discrepancy between the Conditions and Limitation of this Evaluation Report and the proponent’s installation instructions, the Conditions and Limitations of the Report supersede.
- The product must be clearly identified with the phrase “CCMC 14043-R” on its packaging.
This evaluation is based on demonstrated conformance with the following criteria:
|Criteria number||Criteria name|
|CCMC-TG-074633.07-15||CCMC Technical Guide for Heavy Gage PVC Siding|
The Report Holder has submitted technical documentation for the CCMC evaluation. Testing was conducted at laboratories recognized by CCMC. The corresponding technical evidence for this product is summarized below:
|Thermal expansion||°C–1||≤ 8.1 × 10-5||4.8 × 10-5|
|Flammability||–||Compound shall not exceed an average extent of burning of 25 mm, and the average time of burn shall not exceed 10 s||Pass|
|Impact resistance||J||≥ 6.3 J at 23°C||8.2|
|Surface distortion||–||Free from bulges, waves or ripples||Pass|
|Weatherability||–||No peeling, flaking, chipping or pitting||Pass|
|Thickness – Face||mm||≥ 0.7||17|
|Thickness – Nail slots||mm||≥ 0.9||1.9|
|Deformation (sustained pressure)||No fracture or permanent deformation after sustained pressure of 750 Pa for 1 h||Pass|
|Repeated positive and negative pressure test (cyclic pressure), 2 000 cycles||No fracture or permanent deformation after the cyclic pressure 1 090 Pa||Pass|
|Safety test (gust loads)||Resist wind gusts to 1 630 Pa||Pass|
|Flaming||Flaming on or in the wall assembly does not spread more than 5 m above the opening.||Pass|
|Heat flux||Heat flux during the flame exposure on the wall assembly is not more than 35 kW/m2 measured at 3.5 m above the opening.||Pass|
Use of Canadian Construction Materials Centre (CCMC) assessments
This assessment must be read in the context of the entire CCMC Registry of Product Assessments, any applicable building code or by-law requirements, and/or any other regulatory requirements (for example, the Canada Consumer Product Safety Act, the Canadian Environmental Protection Act, etc.).
It is the responsibility of the user to confirm that the assessment they are using is current and has not been withdrawn or superseded by a later version on the CCMC Registry of Product Assessments.
The National Research Council of Canada (NRC) has evaluated only the characteristics of the specific product described herein. The information and opinions in this evaluation are directed to those who have the appropriate degree of experience to use and apply its contents (such as authorities having jurisdiction, design professionals and specifiers). This evaluation is valid when the product is used as part of permitted construction, respecting all conditions and limitations stated in the evaluation, and in accordance with applicable building codes and by-laws.
This evaluation is provided without representation, warranty or guarantee of any kind, expressed or implied, and the NRC provides no endorsement for any evaluated product. The NRC accepts no responsibility whatsoever arising in any way from any and all use of or reliance on the information contained herein or the use of any evaluated product. The NRC is not undertaking to render professional or other services on behalf of any person or entity nor to perform any duty owed by any person or entity to another person or entity.
Une version française de ce document est disponible.
In the case of any discrepancy between the English and French version of this document, the English version shall prevail.
© His Majesty the King in Right of Canada, as represented by the National Research Council of Canada, 2023
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of the CCMC.