Government of Canada / Gouvernement du Canada

Search

[CCMC 13452-R] CCMC Canadian code compliance evaluation

From: National Research Council Canada

In most jurisdictions this document is sufficient evidence for approval by Canadian authorities.

Learn more about CCMC recognition Look for the trusted CCMC mark on products to verify compliance.

Compliance opinion

It is the opinion of the Canadian Construction Materials Centre that the evaluated product, when used as a cold liquid-applied polymerenhanced asphalt for waterproofing below grade foundation walls (concrete or masonry block) in accordance with the conditions and limitations stated in this evaluation, complies with the following code:

National Building Code of Canada 2015

ID Code provision Solution type
09-13-03-01-00-0-009.13.3.1.(1) Where hydrostatic pressure occurs, water ...Acceptable
09-13-03-02-00-0-009.13.3.2.(1) Materials installed to provide required ...Acceptable
09-13-03-04-00-0-009.13.3.4.(1) Unless otherwise stated in this Subsecti ...Alternative
9.13.3.2.(2) +++ Waterproofing MaterialsAlternative

The above opinion(s) is/are based on the evaluation by the CCMC of technical evidence provided by the evaluation holder, and is bound by the stated conditions and limitations. For the benefit of the user, a summary of the technical information that forms the basis of this evaluation has been included.

Product information

Product name

SUPERPRO

Product description

The product is a liquid-applied polymer-enhanced asphalt that is applied with an airless spray to the exterior of foundation walls (concrete or masonry block) to create a 1-mm-thick waterproof membrane.

Manufacturing plant

This evaluation is valid only for products produced at the following plant:

Product nameManufacturing plant
Surrey, BC, CA
SUPERPROProduct evaluated by the CCMC

Product evaluated by the CCMC Indicates that the product from this manufacturing facility has been evaluated by the CCMC

  Conditions and limitations

The CCMC’s compliance opinion is bound by this product being used in accordance with the conditions and limitations set out below.

  • The use of the product has been evaluated for applications falling under the scope of Part 9, Housing and Small Buildings, of Division B of the NBC 2015 for foundation walls at a depth of up to 3 m. The foundation walls must meet the structural requirements of the NBC 2015.
  • The poured in place concrete must be cured prior to the application of the product.
  • The maximum hydrostatic pressure that the membrane can sustain is 48 kPa for five days.
  • Unit masonry or poured-in-place concrete walls must meet the surface preparation requirements of Article 9.13.3.3., Preparation of Surface, of Division B of the NBC 2015.
  • The chemicals (Part A and B of the waterproofing system) must be stored on-site as per the manufacturer’s recommendations.
  • The thickness of the membrane installed throughout the foundation wall must meet the minimum thickness of 1-mm- (40-mils-) thick (dry film) for which the product has been evaluated.

  • While the waterproofing continuity of the membrane to other parts of the wall (e.g., slabs, footing) is beyond the scope of this Evaluation Report, the installer must follow engineer-approved solutions to provide the waterproofing continuity.

  • Following its application, the entire membrane must be protected from exposure to ultraviolet (UV) radiation within two weeks of its application and in accordance with the manufacturer’s additional recommendations.

  • The membrane application must stop at ground level. The exposed above-grade portion of the membrane after soil settling must be protected from UV radiation and mechanical impact with additional backfill that would be graded away from the foundation.
  • The use of the product is limited to installation over foundation walls facing normal soil conditions. When used in soils containing high levels of organic matter, chemicals and microbiological activity, the manufacturer must be consulted to determine suitability.
  • Prior to backfilling, the following conditions and limitations must be followed:
    • The membrane must be first inspected to detect any defects (e.g., holes, tears, bubbles) and be repaired in accordance with the manufacturer’s instructions.
    • The membrane must be covered with a protection board which may consist of a semi-rigid or rigid board with a smooth surface facing the membrane (e.g., mineral fibre boards, EPS/XPS boards or equivalent). The protection boards must not be installed using fasteners in order to avoid penetrations through the membrane. See the manufacturer’s recommendations regarding the use of adhesive and tape to secure the protection boards. Clean sand backfill can be used as an alternative solution to protection boards.
  • The foundation wall must be backfilled in accordance with the requirements of Subsection 9.12.3., Backfill, of Division B of the NBC 2015.
  • The product must be applied by qualified installers in accordance with the manufacturer’s installation instructions using their recommended tools.
  • The product must be identified with the phrase “CCMC 13452-R.”

  Technical information

This evaluation is based on demonstrated conformance with the following criteria:

Evaluation requirements
Criteria number Criteria name
CCMC-TG-071416.01-15CCMC Technical Guide for Liquid-Applied Membrane for Waterproofing Concrete Foundation Wall

 

The Report Holder has submitted technical documentation for the CCMC’s evaluation. Testing was conducted at laboratories recognized by the CCMC. The corresponding technical evidence for this product is summarized below.

Material requirements

Table 1. Results of testing the material requirements of the product
Property Unit Requirement Result
Dry film thickness mm ± 10% of manufacturer’s specified value 1.02
Hardness – Report value 80
Water vapour permeance ng/Pa·s·m2 Report value 55.1
Sag flow mm No sagging 0Table footnote (1)
Pinholing – ≤ 1 pinhole No pinholing
Tensile strength MPa Report value 0.7
Elastic recovery % Report value 73

Performance requirements

Table 2. Results of testing the performance requirements of the product
Property Unit Requirement Result
Watertightness after heat aging – No leakage No leakage
Watertightness after chemical aging – No leakage No leakage
Watertightness after UV exposure – No leakage No leakage
Crack bridging resistance after water immersion – No visible cracking, blistering, peeling or other visible defects No defects
Crack bridging resistance after heat aging – No visible cracking, blistering, peeling or other visible defects No defects
Crack bridging resistance after UV exposure – No visible cracking, blistering, peeling or other visible defects No defects
Peel adhesionTable footnote (1) – initial N/m ≥ 175 1 401
Peel adhesion after water immersion N/m ≥ 90% of original 1 488 (106.2%)
Peel adhesion after heat aging N/m ≥ 90% of original 1 488 (106.2%)
Peel adhesion after UV exposure N/m ≥ 90% of original 1 488 (106.2%)
Tensile strength after heat aging MPa ≥ 90% of original 0.7 (100%)
Tensile strength after chemical aging MPa ≥ 90% of original 0.7 (100%)
Tensile strength after UV exposure MPa ≥ 90% of original 0.7 (100%)
Elastic recovery after heat aging % ≥ 90% of original 73 (100%)
Elastic recovery after chemical aging % ≥ 90% of original 73 (100%)
Elastic recovery after UV exposure % ≥ 90% of original 73 (100%)
Low temperature flexibility – No cracking No cracking

Other technical evidence

Additional performance data requested by the report holder

Results of testing other performance requirements of the product
Time after spraying of membrane Peel adhesion to concrete (N/m) [lb./in.]
4 days 1 476 [8.43]
7 days 2 415 [13.79]
28 days 2 569 [14.1]

Administrative information

Use of Canadian Construction Materials Centre (CCMC) assessments

This assessment must be read in the context of the entire CCMC Registry of Product Assessments, any applicable building code or by-law requirements, and/or any other regulatory requirements (for example, the Canada Consumer Product Safety Act, the Canadian Environmental Protection Act, etc.).

It is the responsibility of the user to confirm that the assessment they are using is current and has not been withdrawn or superseded by a later version on the CCMC Registry of Product Assessments.

Disclaimer

The National Research Council of Canada (NRC) has evaluated only the characteristics of the specific product described herein. The information and opinions in this evaluation are directed to those who have the appropriate degree of experience to use and apply its contents (such as authorities having jurisdiction, design professionals and specifiers). This evaluation is valid when the product is used as part of permitted construction, respecting all conditions and limitations stated in the evaluation, and in accordance with applicable building codes and by-laws.

This evaluation is provided without representation, warranty or guarantee of any kind, expressed or implied, and the NRC provides no endorsement for any evaluated product. The NRC accepts no responsibility whatsoever arising in any way from any and all use of or reliance on the information contained herein or the use of any evaluated product. The NRC is not undertaking to render professional or other services on behalf of any person or entity nor to perform any duty owed by any person or entity to another person or entity.

Language

Une version française de ce document est disponible.
In the case of any discrepancy between the English and French version of this document, the English version shall prevail.

Copyright

© His Majesty the King in Right of Canada, as represented by the National Research Council of Canada, 2023

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of the CCMC.

CCMC recognition

The Canadian Construction Materials Centre (CCMC) assesses compliance with Canadian building, energy and safety codes. We are the only construction code compliance service supported and operated by the Government of Canada. Trusted by over 6,000 regulators across Canada.

Most Canadian authorities having jurisdiction (AHJs) consider CCMC product assessments acceptable as evidence for product approval.

CCMC assessments are recognized by construction authorities across Canada:

The CCMC provides code compliance assessments to Canadian code requirements, consulting nationwide with construction regulators to elicit regional variations in code requirements as well as provincial and local interpretations. Users are advised to review the technical information presented in CCMC assessments when making approval decisions. Learn more about how the CCMC provides a unique service for Canada.

For more information, contact the CCMC by phone at (613) 993-6189 or by email at ccmc@nrc-cnrc.gc.ca

NOTICE

The information presented on this webpage (in HTML format) is the most up-to-date information available from the CCMC about this assessment.

By downloading this PDF you acknowledge that:

  • this PDF is intended for record-keeping purposes only,
  • it represents the information as it was available at the time of downloading, and
  • it may not reflect the latest available information at some future date.
References to this CCMC assessment (in product literature, on websites, etc.) must be made by linking to the evaluation webpage. This PDF must not be used as a means of distributing this assessment to an audience.

View PDF

Code compliance as an acceptable solution

Code Compliance via Acceptable Solutions

If a building design (e.g. material, component, assembly or system) can be shown to meet all provisions of the applicable acceptable solutions in Division B (e.g. it complies with the applicable provisions of a referenced standard), it is deemed to have satisfied the objectives and functional statements linked to those provisions and thus to have complied with that part of the Code.

National Building Code of Canada, Sentence A-1.2.1.1.(1)(a)

The CCMC has determined that compliance with this provision of the Code has been demonstrated as an Acceptable Solution. The evaluation report provides a summary of the basis of CCMC's compliance opinion.

CCMC's code compliance opinions

All CCMC evaluation reports are opinions of code compliance established in accordance with the National Building Code of Canada, Subsection 1.2.1. "Compliance with this Code," which requires compliance to be achieved by:

  • complying with the applicable acceptable solutions in Division B, or
  • using an alternative solution that will achieve at least the minimum level of performance required by Division B in the areas defined by the objective and functional statements attributed to the applicable acceptable solutions.

The CCMC assesses compliance with Canadian building, energy and safety codes, and is trusted by over 6,000 regulators across Canada.

Code compliance as an alternative solution

Code Compliance via Alternative Solutions

Where a design differs from the acceptable solutions in Division B, then it should be treated as an "alternative solution." A proponent of an alternative solution must demonstrate that the alternative solution addresses the same issues as the applicable acceptable solutions in Division B and their attributed objectives and functional statements. However, because the objectives and functional statements are entirely qualitative, demonstrating compliance with them in isolation is not possible. Therefore, Clause 1.2.1.1.(1)(b) identifies the principle that Division B establishes the quantitative performance targets that alternative solutions must meet. In many cases, these targets are not defined very precisely by the acceptable solutions [...] Nevertheless, Clause 1.2.1.1.(1)(b) makes it clear that an effort must be made to demonstrate that an alternative solution will perform as well as a design that would satisfy the applicable acceptable solutions in Division B—not “well enough” but “as well as.”

National Building Code of Canada, Sentence A-1.2.1.1.(1)(b)

The CCMC has determined that compliance with this provision of the Code has been demonstrated as an Alternative Solution. The evaluation report provides a summary of the basis of CCMC's compliance opinion.

CCMC's code compliance opinions

All CCMC evaluation reports are opinions of code compliance established in accordance with the National Building Code of Canada, Subsection 1.2.1. "Compliance with this Code," which requires compliance to be achieved by:

  • complying with the applicable acceptable solutions in Division B, or
  • using an alternative solution that will achieve at least the minimum level of performance required by Division B in the areas defined by the objective and functional statements attributed to the applicable acceptable solutions.

The CCMC assesses compliance with Canadian building, energy and safety codes, and is trusted by over 6,000 regulators across Canada.

Report a problem on this page
Date modified: