[CCMC 13266-L] CCMC Standard compliance evaluation

CCMC number:

13266-L

Status:

Active

Issue date:

2006-12-13

Modified date:

2024-09-09

Evaluation holder:

Holcim Solutions and Products Canada, a Division of Lafarge Canada Inc., Everege Spray Foam Division

6509 Airport Road
Mississauga ON L4V 1S7
Canada
Website: www.holcimelevate.com/ca-en
Telephone: 1-888-292-6265
Email: roofing-ca-hbe@holcim.com

Product names:

Elevate RubberGard™ EPDM SA
Elevate RubberGard™ EcoWhite™ EPDM
Elevate RubberGard™ EcoWhite™ EPDM PT
Elevate RubberGard™ EcoWhite™ Platinum™ EPDM
Elevate RubberGard™ EcoWhite™ Platinum™ EPDM PT
Elevate RubberGard™ LSFR PT
Elevate RubberGard™ Low Slope Fire Retardant (Black)
Elevate RubberGard™ Max EPDM
Elevate RubberGard™ Max PT
Elevate RubberGard™ Platinum
Elevate RubberGard™ Platinum PT

Criteria:

ASTM D4637/D4637M -13, Type I, "Standard Specification for EPDM Sheet Used in Single-Ply Roof Membrane"
ASTM D4637/D4637M -13, Type II, "Standard Specification for EPDM Sheet Used in Single-Ply Roof Membrane"
ASTM D4637/D4637M-15, Type I, "Standard Specification for EPDM Sheet Used in Single-Ply Roof Membrane"

In most jurisdictions this document is sufficient evidence for approval by Canadian authorities.

Learn more about CCMC recognition Look for the trusted CCMC mark on products to verify compliance.

Product information

Product names

Elevate RubberGard™ EPDM SA
Elevate RubberGard™ EcoWhite™ EPDM
Elevate RubberGard™ EcoWhite™ EPDM PT
Elevate RubberGard™ EcoWhite™ Platinum™ EPDM
Elevate RubberGard™ EcoWhite™ Platinum™ EPDM PT
Elevate RubberGard™ LSFR PT
Elevate RubberGard™ Low Slope Fire Retardant (Black)
Elevate RubberGard™ Max EPDM
Elevate RubberGard™ Max PT
Elevate RubberGard™ Platinum
Elevate RubberGard™ Platinum PT

Product description

Type I

The following membranes are single-ply, non-reinforced, ethylene/propylene diene terpolymer (EPDM) roofing membranes available in many thicknesses, widths and lengths:

Elevate RubberGard™ Low Slope Fire Retardant (Black)
Elevate RubberGard™ LSFR PT
Elevate RubberGard™ Platinum
Elevate RubberGard™ Platinum PT
Elevate RubberGard™ EPDM SA

Elevate RubberGard™ Platinum PT and the Elevate RubberGard™ LSFR PT have a QuickSeam™ tape that is either 76.2 mm (3 in.) or 152.4 mm (6 in.) in width and that is factory-laminated continuously along one 30.5 m (100 ft.) length of the panel.

The Elevate RubberGard™ EPDM SA membrane is a self-adhered roof system with Secure Bond Adhesive that is factory-applied to ensure uniform adhesion across the entire membrane.

The following membranes are single-ply, non-reinforced, bi-laminate, white-on-black, cured EPDM roofing membranes:

Elevate RubberGard™ EcoWhite™ EPDM
Elevate RubberGard™ EcoWhite™ EPDM PT
Elevate RubberGard™ EcoWhite™ Platinum™ EPDM
Elevate RubberGard™ EcoWhite™ Platinum™ EPDM PT

Elevate RubberGard™ EcoWhite™ EPDM is 1.52 mm (0.060 in.) thick and comes in lengths of 15.24 m (50 ft.) and 30.5 m (100 ft.), and widths of 3.05 m (10 ft.), 5.08 m (16 ft. 8 in.), 6.1 m (20 ft.), 7.6 m (25 ft.) and 9.4 m (30 ft.).

Elevate RubberGard™ EcoWhite™ EPDM PT has a QuickSeam™ tape that is 76 mm (3 in.) in width and that is factory-laminated continuously along one 30.5 m (100 ft.) length of the panel.

Elevate RubberGard™ EcoWhite™ Platinum™ EPDM is 2.29 mm (0.090 in.) thick and comes in lengths of 15.24 m (50 ft.) and 30.5 m (100 ft.), with a width of 3.05 m (10 ft.).

Elevate RubberGard™ EcoWhite™ Platinum™ PT has a QuickSeam™ tape that is either 76 mm (3 in.) or 152.4 mm (6 in.) in width and that is factory-laminated continuously along one 30.5 m (100 ft.) length of the panel.

Type II

Elevate RubberGard™ Max EPDM and Elevate RubberGard™ Max PT membranes are single-ply, reinforced, black, EPDM roofing membranes that are 3.05 m (10 ft.) wide and 30.5 m (100 ft.) long. Elevate RubberGard™ Max is available in thicknesses of 1.14 mm (45 mil), 1.52 mm (60 mil) and 1.91 mm (75 mil), and Elevate RubberGard™ Max PT is only available in a thickness of 1.52 mm (60 mil).

Elevate RubberGard™ Max PT has a QuickSeam™ tape that is 152.4 mm (6 in.) in width and that is factory-laminated continuously along one 30.5 m (100 ft.) length of the panel.

Manufacturing plant

This evaluation is valid only for products produced at the following plant:

Product names	Manufacturing plant
Product names	Prescott, AR, US
Elevate RubberGard™ EPDM SA	Product evaluated by the CCMC
Elevate RubberGard™ EcoWhite™ EPDM	Product evaluated by the CCMC
Elevate RubberGard™ EcoWhite™ EPDM PT	Product evaluated by the CCMC
Elevate RubberGard™ EcoWhite™ Platinum™ EPDM	Product evaluated by the CCMC
Elevate RubberGard™ EcoWhite™ Platinum™ EPDM PT	Product evaluated by the CCMC
Elevate RubberGard™ LSFR PT	Product evaluated by the CCMC
Elevate RubberGard™ Low Slope Fire Retardant (Black)	Product evaluated by the CCMC
Elevate RubberGard™ Max EPDM	Product evaluated by the CCMC
Elevate RubberGard™ Max PT	Product evaluated by the CCMC
Elevate RubberGard™ Platinum	Product evaluated by the CCMC
Elevate RubberGard™ Platinum PT	Product evaluated by the CCMC

Product evaluated by the CCMC Indicates that the product from this manufacturing facility has been evaluated by the CCMC

Technical information

This evaluation is based on demonstrated conformance with the following criteria:

Evaluation requirements
Criteria number	Criteria name
ASTM D4637/D4637M -13, Type I	Standard Specification for EPDM Sheet Used in Single-Ply Roof Membrane
ASTM D4637/D4637M -13, Type II	Standard Specification for EPDM Sheet Used in Single-Ply Roof Membrane
ASTM D4637/D4637M-15, Type I	Standard Specification for EPDM Sheet Used in Single-Ply Roof Membrane

Additional information

Fire protection

No information at this time.

Wind uplift resistance of membrane roofing assemblies

The wind uplift resistance performance rating is based on CAN/CSA A123.21-14, "Dynamic Wind Uplift Resistance of Membrane-Roofing Systems."

Table 1. Wind uplift performance rating^{Table footnote footnote (1)}
Product	AARS^{Table footnote footnote (2)} – factored load kPa (psf)	MARS^{Table footnote footnote (3)} – factored load kPa (psf)	PARS^{Table footnote footnote (4)} – factored load kPa (psf)
Elevate RubberGard™ Low Slope Fire Retardant (Black)	–2.4 (–50) or –3.9 (–66.7) ^{Table footnote footnote (5)}^{Table footnote footnote (6)}	–3.2 (–67)^{Table footnote footnote (7)}	–3.2 (–67)^{Table footnote footnote (8)}
Elevate RubberGard™ EPDM SA	–2.4 (–50) or –3.9 (–66.7) ^{Table footnote footnote (5)}^{Table footnote footnote (6)}	–3.2 (–67)^{Table footnote footnote (7)}	–3.2 (–67)^{Table footnote footnote (8)}
Elevate RubberGard™ Max	–2.4 (–50) or –3.9 (–66.7) ^{Table footnote footnote (5)}^{Table footnote footnote (6)}	–2.9 (–60)^{Table footnote footnote (9)}	–3.2 (–67)^{Table footnote footnote (8)}
Elevate RubberGard™ Max PT	–2.4 (–50) or –3.9 (–66.7) ^{Table footnote footnote (5)}^{Table footnote footnote (6)}	–2.9 (–60)^{Table footnote footnote (9)}	–3.2 (–67)^{Table footnote footnote (8)}
Elevate RubberGard™ EcoWhite™ EPDM	–2.4 (–50) or –3.9 (–66.7) ^{Table footnote footnote (5)}^{Table footnote footnote (6)}	–3.2 (–67)^{Table footnote footnote (7)}	–3.2 (–67)^{Table footnote footnote (8)}
Elevate RubberGard™ EcoWhite™ EPDM PT	–2.4 (–50) or –3.9 (–66.7) ^{Table footnote footnote (5)}^{Table footnote footnote (6)}	–3.2 (–67)^{Table footnote footnote (7)}	–3.2 (–67)^{Table footnote footnote (8)}
Elevate RubberGard™ EcoWhite™ Platinum™ EPDM	–2.4 (–50) or –3.9 (–66.7) ^{Table footnote footnote (5)}^{Table footnote footnote (6)}	–3.2 (–67)^{Table footnote footnote (7)}	–3.2 (–67)^{Table footnote footnote (8)}
Elevate RubberGard™ EcoWhite™ Platinum™ EPDM PT	–2.4 (–50) or –3.9 (–66.7) ^{Table footnote footnote (5)}^{Table footnote footnote (6)}	–3.2 (–67)^{Table footnote footnote (7)}	–3.2 (–67)^{Table footnote footnote (8)}
Elevate RubberGard™ Platinum	–2.0 (–41)^{Table footnote footnote (10)}	–3.2 (–67)^{Table footnote footnote (7)}	–3.2 (–67)^{Table footnote footnote (8)}
Elevate RubberGard™ Platinum PT	–2.0 (–41)^{Table footnote footnote (10)}	–3.2 (–67)^{Table footnote footnote (7)}	–3.2 (–67)^{Table footnote footnote (8)}
Elevate RubberGard™ LSFR PT	–2.0 (–41)^{Table footnote footnote (10)}	–3.2 (–67)^{Table footnote footnote (7)}	–3.2 (–67)^{Table footnote footnote (8)}

Notes:

Footnote 1

Contact Firestone Building Products Canada for the test reports below or for additional assembly and wind resistance ratings that are not shown here.

Return to table footnote footnote 1 referrer

Footnote 2

AARS = Adhesive Apply Roof System.

Return to table footnote footnote 2 referrer

Footnote 3

MARS = Mechanically Attached Roof System.

Return to table footnote footnote 3 referrer

Footnote 4

PARS = Partially Adhered Roof System.

Return to table footnote footnote 4 referrer

Footnote 5

Depending on the assembly.

Return to table footnote footnote 5 referrer

Footnote 6

See PRI Construction Materials Technologies test report, FBP-393-02-01.

Return to table footnote footnote 6 referrer

Footnote 7

See EXP Services Inc. test report, FPBS-DRS-00225611-01-5100.

Return to table footnote footnote 7 referrer

Footnote 8

See EXP Services Inc. test report, FPBS-DRS-00211230-08-5100.

Return to table footnote footnote 8 referrer

Footnote 9

See EXP Services Inc. test report, FPBS-DRC-00211230-07-5100.

Return to table footnote footnote 9 referrer

Footnote 10

See EXP Services Inc. test report, FPBS-DRC-00225611-03-5100.

Return to table footnote footnote 10 referrer

Administrative information

Use of Canadian Construction Materials Centre (CCMC) assessments

This assessment must be read in the context of the entire CCMC Registry of Product Assessments, any applicable building code or by-law requirements, and/or any other regulatory requirements (for example, the Canada Consumer Product Safety Act, the Canadian Environmental Protection Act, etc.).

It is the responsibility of the user to confirm that the assessment they are using is current and has not been withdrawn or superseded by a later version on the CCMC Registry of Product Assessments.

Disclaimer

The National Research Council of Canada (NRC) has evaluated only the characteristics of the specific product described herein. The information and opinions in this evaluation are directed to those who have the appropriate degree of experience to use and apply its contents (such as authorities having jurisdiction, design professionals and specifiers). This evaluation is valid when the product is used as part of permitted construction, respecting all conditions and limitations stated in the evaluation, and in accordance with applicable building codes and by-laws.

This evaluation is provided without representation, warranty or guarantee of any kind, expressed or implied, and the NRC provides no endorsement for any evaluated product. The NRC accepts no responsibility whatsoever arising in any way from any and all use of or reliance on the information contained herein or the use of any evaluated product. The NRC is not undertaking to render professional or other services on behalf of any person or entity nor to perform any duty owed by any person or entity to another person or entity.

Language

Une version française de ce document est disponible.
In the case of any discrepancy between the English and French version of this document, the English version shall prevail.

Copyright

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of the CCMC.