Government of Canada / Gouvernement du Canada

Search

[CCMC 13198-R] CCMC Canadian code compliance evaluation

From: National Research Council Canada

In most jurisdictions this document is sufficient evidence for approval by Canadian authorities.

Learn more about CCMC recognition Look for the trusted CCMC mark on products to verify compliance.

Compliance opinion

It is the opinion of the Canadian Construction Materials Centre that the evaluated product, when used as a means to install thermal insulation in accordance with the conditions and limitations stated in this evaluation, complies with the following code:

National Building Code of Canada 2015

ID Code provision Solution type
09-25-02-02-01-e-009.25.2.2.(1) Insulation MaterialsAcceptable
09-25-02-04-00-0-009.25.2.4.(4) Where blown-in insulation is installed i ...Acceptable

Ontario Building Code

Ruling No. 11-03-261 (13198-R) authorizing the use of this product in Ontario, subject to the terms and conditions contained in the Ruling, was made by the Minister of Municipal Affairs and Housing on 2011-05-30 (revised 2011-08-16) pursuant to s.29 of the Building Code Act, 1992 (see Ruling for terms and conditions). This Ruling is subject to periodic revisions and updates.

The above opinion(s) is/are based on the evaluation by the CCMC of technical evidence provided by the evaluation holder, and is bound by the stated conditions and limitations. For the benefit of the user, a summary of the technical information that forms the basis of this evaluation has been included.

Product information

Product name

Blow-In-Blanket® System (BIBS®) – Dry

Product description

Using the injection equipment, the loose-fill thermal insulation material is dry-blown into each wall cavity through a pre-cut hole in the nylon netting. The nylon netting, which is used to contain the insulation after installation, is stapled to the interior side of the wood-frame structure.

A drawing depicting the installation of the "Blow-In-Blanket® System(BIBS®)-Dry".

Figure 1. Blow-In-Blanket® System (BIBS®) – Dry

  Conditions and limitations

The CCMC’s compliance opinion is bound by this product being used in accordance with the conditions and limitations set out below.

  • This evaluation applies to Part 9, Housing and Small Buildings, of Division B of the NBC 2015 using conventional wood-frame wall construction.
  • The system must be used with thermal insulation that
    • is listed with a CCMC-recognized certification program,
    • has a CCMC number, or
    • has evidence that the product complies with CAN/ULC-S702-09, “Mineral Fibre Thermal Insulation for Buildings.”
  • The following products have been pre-approved by Blow-In-Blanket® as acceptable thermal insulation to be used in the Blow-In-Blanket® System (BIBS®) – Dry system:
    • Johns Manville Climate Pro and Attic Protector Blowing Wool Insulation (CCMC 12642-L),
    • Jet Stream® MAX , CCMC 13404-L, JetStream® MAX Blowing Insulation Wall System (CCMC 13422-R),
    • InsulSafe® XC Wall Insulation System (CCMC 13272-R), and
    • Johns Manville Spider® Plus Custom Insulation System (CCMC 13212-R).
  • Installers must be manufacturer-approved, must use approved equipment, and must follow the conditions and limitations specified in this Report.
  • The thermal insulation product must be delivered to the building site in unopened packages.
  • The netting must not bulge more than 13 mm beyond the stud in order to provide the necessary product density.
  • The insulation must be kept away from heat-emitting devices, such as recessed light fixtures, chimneys, and propane or natural gas sources, at a distance of at least 75 mm or the distance required by the local authority having jurisdiction (AHJ).
  • The installation must be in accordance with the manufacturer’s installation instructions
  • For coverage charts, refer to product literature from the respective thermal insulation manufacturers.
  • The products used with the Blow-In-Blanket® System (BIBS®) – Dry system shall be clearly identified with the CCMC # and manufacturer name.

  Technical information

This evaluation is based on demonstrated conformance with the following criteria:

Evaluation requirements
Criteria number Criteria name
CCMC-TG-072126.02-15CCMC Technical Guide for Blown Mineral Fibre Insulation System with Netting for Walls

Material requirements

The thermal insulation product meets the requirements in CAN/ULC-S702, Type 5.

Performance requirements

Table 1. Results of testing the performance properties of the product

Property

Unit

Requirement

Result

Bulge

38 mm × 89 mm: studs at 400 mm on centre (o.c.)

mm

13

Pass

38 mm × 140 mm: studs at 600 mm o.c.

mm

13

Pass

Design density

38 mm × 89 mm: studs at 400 mm o.c.

kg/m3

≥ 25 or proponent's design density

Pass

38 mm × 140 mm: studs at 600 mm o.c.

kg/m3

≥ 25 or proponent's design density

Pass

Density deviation from each stud space

38 mm × 89 mm: studs at 400 mm o.c.

%

± 10% of design density

Pass

38 mm × 140 mm: studs at 600 mm o.c.

%

± 10% of design density

Pass

Thermal resistance at 150 mm

38 mm × 89 mm: studs at 400 mm o.c.

m2·K/W

≥ 3.6

Pass

38 mm × 140 mm: studs at 600 mm o.c.

m2·K/W

≥ 3.6

Pass

Administrative information

Use of Canadian Construction Materials Centre (CCMC) assessments

This assessment must be read in the context of the entire CCMC Registry of Product Assessments, any applicable building code or by-law requirements, and/or any other regulatory requirements (for example, the Canada Consumer Product Safety Act, the Canadian Environmental Protection Act, etc.).

It is the responsibility of the user to confirm that the assessment they are using is current and has not been withdrawn or superseded by a later version on the CCMC Registry of Product Assessments.

Disclaimer

The National Research Council of Canada (NRC) has evaluated only the characteristics of the specific product described herein. The information and opinions in this evaluation are directed to those who have the appropriate degree of experience to use and apply its contents (such as authorities having jurisdiction, design professionals and specifiers). This evaluation is valid when the product is used as part of permitted construction, respecting all conditions and limitations stated in the evaluation, and in accordance with applicable building codes and by-laws.

This evaluation is provided without representation, warranty or guarantee of any kind, expressed or implied, and the NRC provides no endorsement for any evaluated product. The NRC accepts no responsibility whatsoever arising in any way from any and all use of or reliance on the information contained herein or the use of any evaluated product. The NRC is not undertaking to render professional or other services on behalf of any person or entity nor to perform any duty owed by any person or entity to another person or entity.

Language

Une version française de ce document est disponible.
In the case of any discrepancy between the English and French version of this document, the English version shall prevail.

Copyright

© His Majesty the King in Right of Canada, as represented by the National Research Council of Canada, 2023

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of the CCMC.

CCMC recognition

The Canadian Construction Materials Centre (CCMC) assesses compliance with Canadian building, energy and safety codes. We are the only construction code compliance service supported and operated by the Government of Canada. Trusted by over 6,000 regulators across Canada.

Most Canadian authorities having jurisdiction (AHJs) consider CCMC product assessments acceptable as evidence for product approval.

CCMC assessments are recognized by construction authorities across Canada:

The CCMC provides code compliance assessments to Canadian code requirements, consulting nationwide with construction regulators to elicit regional variations in code requirements as well as provincial and local interpretations. Users are advised to review the technical information presented in CCMC assessments when making approval decisions. Learn more about how the CCMC provides a unique service for Canada.

For more information, contact the CCMC by phone at (613) 993-6189 or by email at ccmc@nrc-cnrc.gc.ca

NOTICE

The information presented on this webpage (in HTML format) is the most up-to-date information available from the CCMC about this assessment.

By downloading this PDF you acknowledge that:

  • this PDF is intended for record-keeping purposes only,
  • it represents the information as it was available at the time of downloading, and
  • it may not reflect the latest available information at some future date.
References to this CCMC assessment (in product literature, on websites, etc.) must be made by linking to the evaluation webpage. This PDF must not be used as a means of distributing this assessment to an audience.

View PDF

Code compliance as an acceptable solution

Code Compliance via Acceptable Solutions

If a building design (e.g. material, component, assembly or system) can be shown to meet all provisions of the applicable acceptable solutions in Division B (e.g. it complies with the applicable provisions of a referenced standard), it is deemed to have satisfied the objectives and functional statements linked to those provisions and thus to have complied with that part of the Code.

National Building Code of Canada, Sentence A-1.2.1.1.(1)(a)

The CCMC has determined that compliance with this provision of the Code has been demonstrated as an Acceptable Solution. The evaluation report provides a summary of the basis of CCMC's compliance opinion.

CCMC's code compliance opinions

All CCMC evaluation reports are opinions of code compliance established in accordance with the National Building Code of Canada, Subsection 1.2.1. "Compliance with this Code," which requires compliance to be achieved by:

  • complying with the applicable acceptable solutions in Division B, or
  • using an alternative solution that will achieve at least the minimum level of performance required by Division B in the areas defined by the objective and functional statements attributed to the applicable acceptable solutions.

The CCMC assesses compliance with Canadian building, energy and safety codes, and is trusted by over 6,000 regulators across Canada.

Code compliance as an alternative solution

Code Compliance via Alternative Solutions

Where a design differs from the acceptable solutions in Division B, then it should be treated as an "alternative solution." A proponent of an alternative solution must demonstrate that the alternative solution addresses the same issues as the applicable acceptable solutions in Division B and their attributed objectives and functional statements. However, because the objectives and functional statements are entirely qualitative, demonstrating compliance with them in isolation is not possible. Therefore, Clause 1.2.1.1.(1)(b) identifies the principle that Division B establishes the quantitative performance targets that alternative solutions must meet. In many cases, these targets are not defined very precisely by the acceptable solutions [...] Nevertheless, Clause 1.2.1.1.(1)(b) makes it clear that an effort must be made to demonstrate that an alternative solution will perform as well as a design that would satisfy the applicable acceptable solutions in Division B—not “well enough” but “as well as.”

National Building Code of Canada, Sentence A-1.2.1.1.(1)(b)

The CCMC has determined that compliance with this provision of the Code has been demonstrated as an Alternative Solution. The evaluation report provides a summary of the basis of CCMC's compliance opinion.

CCMC's code compliance opinions

All CCMC evaluation reports are opinions of code compliance established in accordance with the National Building Code of Canada, Subsection 1.2.1. "Compliance with this Code," which requires compliance to be achieved by:

  • complying with the applicable acceptable solutions in Division B, or
  • using an alternative solution that will achieve at least the minimum level of performance required by Division B in the areas defined by the objective and functional statements attributed to the applicable acceptable solutions.

The CCMC assesses compliance with Canadian building, energy and safety codes, and is trusted by over 6,000 regulators across Canada.

Report a problem on this page
Date modified: