Language selection

Government of Canada / Gouvernement du Canada

Search

[CCMC 13067-R] CCMC Canadian code compliance evaluation

In most jurisdictions this document is sufficient evidence for approval by Canadian authorities.

Learn more about CCMC recognition Look for the trusted CCMC mark on products to verify compliance.

Compliance opinion

It is the opinion of the Canadian Construction Materials Centre that the evaluated product, when used as a cold liquid-applied polymer-enhanced asphalt in accordance with the conditions and limitations stated in this evaluation, complies with the following code:

National Building Code of Canada 2010

ID Code provision Solution type
09-13-03-01-00-0-009.13.3.1. Required WaterproofingAcceptable
09-13-03-02-00-0-009.13.3.2. Material StandardsAcceptable
09-13-03-03-00-0-009.13.3.3. Standards for ApplicationAcceptable
09-13-03-05-00-0-009.13.3.5. Application of Waterproofing MembranesAcceptable

Ontario Building Code

Ruling No. 04-11-115 (13067-R) authorizing the use of this product in Ontario, subject to the terms and conditions contained in the Ruling, was made by the Minister of Municipal Affairs and Housing on 2009-08-14 (revised 2019-08-02) pursuant to s.29 of the Building Code Act, 1992 (see Ruling for terms and conditions). This Ruling is subject to periodic revisions and updates.

The above opinion(s) is/are based on the evaluation by the CCMC of technical evidence provided by the evaluation holder, and is bound by the stated conditions and limitations. For the benefit of the user, a summary of the technical information that forms the basis of this evaluation has been included.

Product information

Product name

WatchDog®

Product description

The product is a single component, liquid-applied, polymer-enhanced asphalt that is applied with a high pressure airless spray to the exterior of foundation walls (poured-in-place concrete or unit masonry) to create a waterproofing membrane that is 1–3 mm thick (dry film).

Manufacturing plant

This evaluation is valid only for products produced at the following plant:

Product nameManufacturing plant
Medina, OH, US
WatchDog®Product evaluated by the CCMC

Product evaluated by the CCMC Indicates that the product from this manufacturing facility has been evaluated by the CCMC

  Conditions and limitations

The CCMC’s compliance opinion is bound by this product being used in accordance with the conditions and limitations set out below.

  • Use of the product has been evaluated for application depths not more than 3 m as covered in Part 9 of Division B of the NBC 2010.
  • The foundation wall must be backfilled in accordance with the NBC 2010.
  • The poured-in-place concrete wall must be cured prior to the application of the product.
  • The maximum hydrostatic pressure that the membrane can sustain is 48 kPa for five days.
  • Unit masonry and poured-in-place concrete walls must meet the surface preparation requirements of Article 9.13.3.4., Preparation of Surface, and Article 9.13.2.4., Preparation of Surface, of Division B of the NBC 2010.
  • Backfill must be placed in a manner that does not damage the foundation wall or the waterproof membrane. The foundation wall must be backfilled in accordance with the requirements of Subsection 9.12.3., Backfill, of Division B of the NBC 2010.
  • The product must be applied by installers qualified and approved by Tremco Barrier Solutions, Inc. in accordance with the manufacturer’s conditions, procedures, and directions.
  • The thickness of the membrane installed throughout the foundation wall must meet the minimum dry-film thickness of the evaluated product.
  • While the waterproofing continuity of the membrane to other parts of the wall (e.g., slabs, footings) is beyond the scope of this Evaluation Report, the installer must follow engineer-approved solutions to provide the waterproofing continuity.
  • The membrane application must stop at ground level. The exposed above-grade portion of the membrane after soil settling must be protected from UV radiation and mechanical impact with additional backfill that would be graded away from the foundation.
  • The use of the product is limited to installation over foundation walls facing normal soil conditions. When used in soils containing high levels of organic matter, chemicals and microbiological activity, the manufacturer must be consulted to determine the suitability of installation.
  • Following its application, the entire membrane must be protected from exposure to ultraviolet (UV) radiation within three weeks of its application and in accordance with the manufacturer’s additional recommendations.
  • The wall and footings must be dry and free of dirt during application.
  • Any water must be removed from the concrete surface and it must be dry prior to application of the product.
  • Prior to backfilling:
    • The membrane must be first inspected to detect any defects (e.g., holes, tears, bubbles) and be repaired in accordance with the manufacturer’s instructions.
    • The membrane must be covered with a protection board that consists of a semi-rigid or rigid board with a smooth surface facing the membrane (e.g., mineral fibre boards, expanded polystyrene/extruded polystyrene (EPS/XPS) boards or other equivalent board). The protection boards must not be installed using fasteners to prevent penetrations through the membrane below grade. See the manufacturer’s recommendations regarding the use of adhesive and tape to secure the protection boards.
  • The product must be clearly identified with the phrase “CCMC 13067-R.”

  Technical information

This evaluation is based on demonstrated conformance with the following criteria:

Evaluation requirements
Criteria number Criteria name
CCMC-TG-071416.01-10CCMC Technical Guide for Liquid-Applied Membrane for Waterproofing Concrete Foundation Wall

The Report Holder has submitted technical documentation for the CCMC’s evaluation. Testing was conducted at laboratories recognized by the CCMC. The corresponding technical evidence for this product is summarized below.

Material requirements

Material physical properties test results
Property Unit Requirement Results
Dry film thickness mm Measured values must be ± 10% of the manufacturer's specified value (report the manufacturer's declared value) 1.02
Tensile strength kPa Report value 171
Specific gravity – Report value 0.925
Water absorption % ≤ 3 2.9
Low temperature flexibility – No cracking (naked eye) Pass

Performance requirements

Table 1. Performance property test results
Property Unit Requirement Results
Puncture resistance – No perforation (29 N static load applied for 24 h)  Pass
Impact resistance at 23°C J Report values 7.8
Impact resistance at −10°C J Report values 5.6
Impact resistance watertightness after impact J No leakage after impact Pass
Crack bridging/cyclic movement resistance at 20°C – No visible cracking, blistering or other defects visible to the naked eye Pass
Crack bridging/cyclic movement resistance at 30 cycles (un-aged specimen) –
Crack bridging/cyclic movement resistance at 5 cycles (aged specimen) –
Peel adhesionTable footnote (1) after water immersion N/m ≥ 175 699
Chemical resistance hydrochloric acid (10%) – No loss of film integrity Pass
Chemical resistance lime water saturated – No loss of film integrity Pass
Chemical resistance sodium hydroxide (10%) – No loss of film integrity Pass
Accelerated weathering tensile strength after exposure % No deterioration of film ≥ 90% of original value (see Table "Material physical properties test results") Pass

Administrative information

Use of Canadian Construction Materials Centre (CCMC) assessments

This assessment must be read in the context of the entire CCMC Registry of Product Assessments, any applicable building code or by-law requirements, and/or any other regulatory requirements (for example, the Canada Consumer Product Safety Act, the Canadian Environmental Protection Act, etc.).

It is the responsibility of the user to confirm that the assessment they are using is current and has not been withdrawn or superseded by a later version on the CCMC Registry of Product Assessments.

Disclaimer

The National Research Council of Canada (NRC) has evaluated only the characteristics of the specific product described herein. The information and opinions in this evaluation are directed to those who have the appropriate degree of experience to use and apply its contents (such as authorities having jurisdiction, design professionals and specifiers). This evaluation is valid when the product is used as part of permitted construction, respecting all conditions and limitations stated in the evaluation, and in accordance with applicable building codes and by-laws.

This evaluation is provided without representation, warranty or guarantee of any kind, expressed or implied, and the NRC provides no endorsement for any evaluated product. The NRC accepts no responsibility whatsoever arising in any way from any and all use of or reliance on the information contained herein or the use of any evaluated product. The NRC is not undertaking to render professional or other services on behalf of any person or entity nor to perform any duty owed by any person or entity to another person or entity.

Language

Une version française de ce document est disponible.
In the case of any discrepancy between the English and French version of this document, the English version shall prevail.

Copyright

© His Majesty the King in Right of Canada, as represented by the National Research Council of Canada, 2024

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of the CCMC.

CCMC recognition

The Canadian Construction Materials Centre (CCMC) assesses compliance with Canadian building, energy and safety codes. We are the only construction code compliance service supported and operated by the Government of Canada. Trusted by over 6,000 regulators across Canada.

Most Canadian authorities having jurisdiction (AHJs) consider CCMC product assessments acceptable as evidence for product approval.

CCMC assessments are recognized by construction authorities across Canada:

The CCMC provides code compliance assessments to Canadian code requirements, consulting nationwide with construction regulators to elicit regional variations in code requirements as well as provincial and local interpretations. Users are advised to review the technical information presented in CCMC assessments when making approval decisions. Learn more about how the CCMC provides a unique service for Canada.

For more information, contact the CCMC by phone at (613) 993-6189 or by email at ccmc@nrc-cnrc.gc.ca

NOTICE

The information presented on this webpage (in HTML format) is the most up-to-date information available from the CCMC about this assessment.

By downloading this PDF you acknowledge that:

  • this PDF is intended for record-keeping purposes only,
  • it represents the information as it was available at the time of downloading, and
  • it may not reflect the latest available information at some future date.
References to this CCMC assessment (in product literature, on websites, etc.) must be made by linking to the evaluation webpage. This PDF must not be used as a means of distributing this assessment to an audience.

View PDF

Code compliance as an acceptable solution

Code Compliance via Acceptable Solutions

If a building design (e.g. material, component, assembly or system) can be shown to meet all provisions of the applicable acceptable solutions in Division B (e.g. it complies with the applicable provisions of a referenced standard), it is deemed to have satisfied the objectives and functional statements linked to those provisions and thus to have complied with that part of the Code.

National Building Code of Canada, Sentence A-1.2.1.1.(1)(a)

The CCMC has determined that compliance with this provision of the Code has been demonstrated as an Acceptable Solution. The evaluation report provides a summary of the basis of CCMC's compliance opinion.

CCMC's code compliance opinions

All CCMC evaluation reports are opinions of code compliance established in accordance with the National Building Code of Canada, Subsection 1.2.1. "Compliance with this Code," which requires compliance to be achieved by:

  • complying with the applicable acceptable solutions in Division B, or
  • using an alternative solution that will achieve at least the minimum level of performance required by Division B in the areas defined by the objective and functional statements attributed to the applicable acceptable solutions.

The CCMC assesses compliance with Canadian building, energy and safety codes, and is trusted by over 6,000 regulators across Canada.

Code compliance as an alternative solution

Code Compliance via Alternative Solutions

Where a design differs from the acceptable solutions in Division B, then it should be treated as an "alternative solution." A proponent of an alternative solution must demonstrate that the alternative solution addresses the same issues as the applicable acceptable solutions in Division B and their attributed objectives and functional statements. However, because the objectives and functional statements are entirely qualitative, demonstrating compliance with them in isolation is not possible. Therefore, Clause 1.2.1.1.(1)(b) identifies the principle that Division B establishes the quantitative performance targets that alternative solutions must meet. In many cases, these targets are not defined very precisely by the acceptable solutions [...] Nevertheless, Clause 1.2.1.1.(1)(b) makes it clear that an effort must be made to demonstrate that an alternative solution will perform as well as a design that would satisfy the applicable acceptable solutions in Division B—not “well enough” but “as well as.”

National Building Code of Canada, Sentence A-1.2.1.1.(1)(b)

The CCMC has determined that compliance with this provision of the Code has been demonstrated as an Alternative Solution. The evaluation report provides a summary of the basis of CCMC's compliance opinion.

CCMC's code compliance opinions

All CCMC evaluation reports are opinions of code compliance established in accordance with the National Building Code of Canada, Subsection 1.2.1. "Compliance with this Code," which requires compliance to be achieved by:

  • complying with the applicable acceptable solutions in Division B, or
  • using an alternative solution that will achieve at least the minimum level of performance required by Division B in the areas defined by the objective and functional statements attributed to the applicable acceptable solutions.

The CCMC assesses compliance with Canadian building, energy and safety codes, and is trusted by over 6,000 regulators across Canada.

Page details

From: National Research Council Canada

Date modified: