Company name | Mitutoyo Canada Inc. Calibration Laboratory |
---|---|
Company address | 2121 Meadowvale Mississauga, Ontario L5N 5N1 |
Contact | Gary Mueller Telephone: 905-821-1261 Fax: 905-821-4968 Email: gary.mueller@mitutoyo.ca |
Clients served |
|
Fields of calibration |
|
Accreditation body |
|
ISO/IEC 17025 |
|
This CLAS Certificate is published by the CLAS service of the National Research Council of Canada (NRC) in cooperation with the laboratory accreditation program of the accreditation body. The accreditation body recognizes the capability of the named laboratory for being able to perform calibrations as per the listed Calibration and Measurement Capabilities with metrological traceability to the International System of Units (SI) or to standards acceptable to CLAS. See supplementary notes.
Measured Quantity & Range or Instrument | Expanded Measurement Uncertainty | Type of Service | Remarks |
---|---|---|---|
Gauge block CLTM-7 See note 1 |
|||
Steel, length | |||
Inch, up to 4 inches | ( 1.6 + 0.8 L ) µinch (L in inches) or 2 µinch, whichever greater |
I | Using automatic comparator |
Metric, up to 100 mm | ( 0.041+ 0.0008 L ) µm (L in mm) or 0.05 µm, whichever greater |
Using automatic comparator | |
Inch, up to 1 inch | ( 4 + 0.7 L ) µinch (L in inches) |
Using manual comparator; direct comparison | |
Metric, up to 25 mm | ( 0.11+ 0.0007 L ) µm (L in mm) |
Using manual comparator; direct comparison | |
Inch, up to 1 inch | ( 7+ 0.7 L ) µinch (L in inches) |
Using manual comparator; wide-range | |
Metric, up to 25 mm | ( 0.18+ 0.0007 L ) µm (L in mm) |
Using manual comparator; wide-range | |
Inch, 1 inch to 10 inches | ( 5 + 5.5 L ) µinch (L in inches) |
Using manual comparator; direct comparison | |
Metric, 25 mm to 250 mm | ( 0.13+ 0.0055 L ) µm (L in mm) |
Using manual comparator; direct comparison | |
Inch, 12 inches to 20 inches | 47 µinch | Using CMM | |
Metric, 300 mm to 500 mm | 1.2 µm | Using CMM | |
Ceramic, length See note 1 |
|||
Inch, up to 4 inches | ( 1.6+ 0.7 L ) µinch (L in inches) or 2 µinch, whichever greater |
I | Using automatic comparator |
Metric, up to 100 mm | ( 0.04+ 0.0007 L ) µm (L in mm) or 0.05 µm, whichever greater |
Using automatic comparator | |
Gauge Block See note 2 |
|||
Variation in length (parallelism) | 1 µinch or 0.025 µm |
I | Using automatic comparator |
Height gauge | |||
Inch, up to 40 inches | ( 51+ 2.0 L ) µinch (L in inches) |
II | See note 3 |
Metric, up to 1000 mm | ( 1.3+ 0.002 L ) µm (L in mm) |
||
Micrometer | |||
Head | |||
Inch, up to 2 inches | 30 µinch | II | See note 3 |
Metric, up to 50 mm | 0.6 µm | ||
Outside | |||
Inch, up to 6 inches | ( 45 + 2 L ) µinch (L in inches) |
II | See note 3 |
Inch, > 6 inches to 20 inches | ( 50 + 4.2 L ) µinch (L in inches) |
||
Metric, up to 500 mm | ( 1.0 + 0.0042 L ) µm (L in mm) |
||
Depth | |||
Inch, up to 6 inches | ( 45 + 2.2 L ) µinch (L in inches) |
II | See note 3 |
Inch, > 6 inches to 12 inches | ( 55 + 3.8 L ) µinch (L in inches) |
||
Metric, up to 300 mm | ( 1.1 + 0.0036 L ) µm (L in mm) |
||
Tubular inside | |||
Inch, up to 2 inches | ( 50 + 0.8 L ) µinch (L in inches) |
II | See note 3 |
Inch, > 2 inches to 24 inches | ( 60 + 4.4 L ) µinch (L in inches) |
||
Metric, up to 600 mm | ( 1.0 + 0.005 L ) µm (L in mm) |
||
Three point internal | |||
Inch, up to 4 inches | ( 52 + 2.2 L ) µinch (L in inches) |
II | See note 3 |
Inch, 4 inches to 8 inches | ( 75 + 1.9 L ) µinch (L in inches) |
||
Metric, up to 100 mm | ( 1.3 + 0.0022 L ) µm (L in mm) |
||
Metric, 100 mm to 200 mm | ( 1.9 + 0.0019 L ) µm (L in mm) |
||
Indicator tester | |||
Inch, up to 1 inch | 30 µinch | II | See note 3 |
Metric, up to 25 mm | 0.6 µm | ||
Bore gauge (2 points) | |||
Inch, up to 4 inches | ( 50 + 0.3 L ) µinch (L in inches) |
II | See note 3 |
Metric, up to 100 mm | ( 1.1 + 0.0006 L ) µm (L in mm) |
||
Indicator | |||
Dial | |||
Inch, 0.00005 inch graduations | 14 µinch | II | Up to 4 inch travel |
Inch, 0.0001 inch graduations | 20 µinch | ||
Metric, 0.001 mm graduations | 0.3 µm | Up to 100 mm travel | |
Metric, 0.002 mm graduations | 0.4 µm | ||
Metric, 0.02 mm graduations | 3.0 µm | ||
Digital | |||
Inch, 0.00005 inch resolution | 30 µinch | II | Up to 4 inch travel |
Metric, 0.0005 mm resolution | 0.4 µm | Up to 100 mm travel | |
Metric, 0.001 mm resolution | 0.7 µm | ||
Metric, 0.01 mm resolution | 5.8 µm | ||
Caliper | |||
Outside, Inside and Depth | |||
Inch | |||
up to 24 inches | ( 290 + 1.6 L ) µinch (L in inches) |
II | See note 1 |
> 24 inches to 40 inches | |||
0.0005 inch resolution | ( 400 + 14 L ) µinch (L in inches) |
II | See note 1 |
0.001 inch resolution | ( 1000 + 10 L ) µinch (L in inches) |
||
Metric | |||
up to 600 mm | ( 5.8 + 0.002 L ) µm (L in mm) |
II | See note 1 |
> 600 mm to 1000 mm | |||
0.01 mm resolution | ( 7.5 + 0.014 L ) µm (L in mm) |
II | See note 1 |
0.02 mm resolution | ( 20 + 0.010 L ) µm (L in mm) |
||
Depth gauge | |||
Dial Caliper Type | |||
Inch, up to 12 inches | 0.0024 inch | II | See note 3 |
Metric, up to 300 mm | 60 µm | ||
Dial Indicator Type | |||
Inch, up to 12 inches | 580 µinch | II | See note 3 |
Metric, up to 300 mm | 12 µm | ||
Digital Caliper Type | |||
Inch, up to 12 inches | 290 µinch | II | See note 3 |
Metric, up to 300 mm | 6 µm | ||
Digital Indicator Type | |||
Inch, up to 12 inches | ( 30 + 2 L ) µinch (L in inches) |
II | See note 3 |
Metric, up to 300 mm | ( 0.6 + 0.0025 L ) µm (L in mm) |
||
Vernier Caliper Type | |||
Inch, up to 12 inches | 1200 µinch | II | See note 3 |
Metric, up to 300 mm | 24 µm | ||
External caliper gauge | |||
Inch, up to 4 inches | |||
0.0002 inch resolution | 120 µinch | II | See note 1 |
0.0005 inch resolution | 290 µinch | ||
0.001 inch resolution | 580 µinch | ||
0.002 inch resolution | 1200 µinch | ||
0.005 inch resolution | 2900 µinch | ||
Metric, up to 100 mm | |||
0.005 mm resolution | 2.9 µm | II | See note 1 |
0.01 mm resolution | 5.8 µm | ||
0.02 mm resolution | 12 µm | ||
0.05 mm resolution | 29 µm | ||
0.1 mm resolution | 58 µm | ||
Internal caliper gauge | |||
Inch, up to 4 inches | |||
0.0002 inch resolution | 120 µinch | II | See note 1 |
0.0005 inch resolution | 290 µinch | ||
0.001 inch resolution | 580 µinch | ||
Metric, up to 100 mm | |||
0.005 mm resolution | 2.9 µm | II | See note 1 |
0.01 mm resolution | 5.8 µm | ||
0.02 mm resolution | 12 µm | ||
Thickness gauge | |||
Inch, up to 1 inch | 290 µinch | II | See note 3 |
Metric, up to 25 mm | 5.8 µm | ||
Profile projector | |||
Linearity of movement: Digital readout type |
( 1.6 + 0.021 L ) µm (L in mm) |
III | See note 3 On-site calibration available. |
Linearity of movement: Micrometer head type |
( 1.6 + 0.017 L ) µm (L in mm) |
||
Magnification error | ( 13+0.017 L ) µm (L in mm) |
||
Squareness of stage | 0.7 µm | ||
Eccentricity of screen rotation | 1.6 µm | ||
Parallelism of stage | 1.7 µm | ||
Accuracy of edge finder | 1.0 µm | ||
I-Checker | |||
0 mm to 100 mm | ( 0.13 +. 0027 L ) μm , L is in mm | II | See note 1 |
0 inches to 4 inches | ( 5.1 + 2.7 L ) μinch , L is in inch | ||
Mu-checker: Graduation | |||
0.1 μm | 0.3 μm | II | See note 1 |
0.5 μm | 0.3 μm | ||
1 μm | 0.4 μm | ||
5 μm | 1.5 μm | ||
10 μm | 2.9 μm | ||
50 μm | 15 μm | ||
0.000005 inch | 10 μinch | ||
0.00001 inch | 10 μinch | ||
0.00005 inch | 17 μinch | ||
0.0001 inch | 30 μinch | ||
0.0005 inch | 150 μinch | ||
0.001 inch | 290 μinch | ||
Riser block | |||
150 mm to 600 mm | ( 0.4 + 0.002 L ) μm , L is in mm | II | See note 1 |
6 inches to 24 inches | ( 16 + 2 L ) μinch , L is in inch | ||
Height masters | |||
Up to 300 mm | ( 0.5 + 0.002 L ) μm , L is in mm | II | See note 1 |
Up to 12 inches | ( 20 + 2 L ) μinch , L is in inch | ||
Step gauge (checkmaster) | |||
Up to 1010 mm | ( 0.39 + 0.0014 L ) µm where L is the length in mm |
II | See note 13 |
> 1010 mm to 1710 mm | ( 0.61 + 0.0018 L ) µm where L is the length in mm |
||
Up to 40 inch | ( 15.4 + 1.4 L ) µinch where L is the length in inches |
||
> 40 Inch up to 70 Inch | ( 24 + 1.8 L ) µinch where L is the length in inches |
||
Micrometer standard | |||
5 mm to 500 mm | ( 0.32 + 0.002 L ) µm where L is the length in mm |
II | See note 13 |
> 500 mm to 1000 mm | ( 0.69 + 0.004 L ) µm where L is the length in mm |
||
0.2 inches to 20 inches | ( 12.6 + 2 L ) µinch where L is the length in inches |
||
> 20 inches to 40 inches | ( 27.2 + 4 L ) µinch where L is the length in inches | ||
Flatness for granite or steel surfaces requiring an accuracy of greater than 0.4 µm |
|||
1 mm x 1 mm to 900 mm x 1000 mm | ( 0.34 + 0.002 L ) µm where L is the maximum length in mm |
II | See note 15 |
0.04 inches x 0.04 inches to 35 inches x 40 inches | ( 13 + 2 L ) µinch where L is the maximum length in inches |
||
Cylindrical ring gauge: Diameter | |||
3 mm to 500 mm | ( 0.46 + 0.002D ) µm where D is the diameter in mm |
II | See note 13 |
0.12 inches to 20 inches | ( 18.1 + 2.0D ) µinch where D is the diameter in inches |
||
Cylindrical plug gauges: Diameter | |||
3 mm to 500 mm | ( 0.30 + 0.002D ) µm where D is the diameter in mm |
II | See note 13 |
0.12 inches to 20 inches | ( 11.8 + 2.0D ) µinch where D is the diameter in inches |
||
Test spheres | |||
Diameter | |||
8 mm to 50 mm | 0.4 µm | II | See note 13 |
0.3 inches to 2 inches | 16 µinch | ||
Form | |||
8 mm to 50 mm | ( 0.05 + 0.007R ) µm where R is the measured roundness in µm |
II | See note 14 |
0.3 inches to 2 inches | ( 2.0 + 0.007R ) µinch where R is the measured roundness in µinch |
||
Roundness | |||
Diameter of 2 mm to 200 mm | ( 0.05 + 0.007R ) µm where R is the measured roundness in µm |
II | See note 14 |
Diameter of 0.8 inches to 8 inches | ( 2.0 + 0.007R ) µinch where R is the measured roundness in µinch |
||
Precision squares | |||
50 mm to 800 mm | ( 0.3 + 0.003 L ) µm where L is the length in mm |
II | See note 15 |
2 inches to 32 inches | ( 12 + 3 L ) µinch where L is the length in inches |
||
Parallels: Granite or steel | |||
5 mm to 1000 mm | |||
Parallelism | ( 0.33 + 0.002 L ) µm where L is the length in mm |
II | See note 13 |
Width | ( 0.83 + 0.001 L ) µm where L is the length in mm |
||
0.2 inches to 40 inches | |||
Parallelism | ( 13.0 + 2 L ) µinch where L is the length in inches |
II | See note 13 |
Width | ( 32.7 + 1.0 L ) µinch where L is the length in inches |
||
Mitutoyo contracer and form tracers | |||
Up to 200 mm Horizontal Axis: | |||
Measurement of Stylus Radius | ( 1.21 + 0.004D ) µm where D is measured Radius length in mm |
III | On-site services as per FSTM-11 |
Detector Accuracy | ( 0.33 + 0.0007L ) µm where L is the length in mm |
||
X and Y Axis | ( 0.63 + 0.004L ) µm where L is measurement length in mm |
||
Straightness | 0.09 µm | ||
Surface roughness | 0.07 µm | ||
Coordinate measuring machines (CMM) | |||
Acceptance and reverification tests for CMM - CMMs used for measuring size | On-site services as per ISO 10360-2 2009 edition and 2001 edition. See note 9 |
||
Error of Indication | |||
0 m to 1.5 m | ( 0.12 + 0.00004 L ) µm where L is the length in mm |
III | See note 10 |
0 m to 40 m | ( 0.16 + 0.0006 L ) µm where L is the length in mm |
See note 11 | |
Probing Error | |||
10 mm to 50 mm in sphere diameter |
0.14 µm | III | See note 12 |
Mitutoyo optic coordinate measuring machines | |||
Up to 600 mm | |||
Length Measurement Error: EUXY | (0.25 + 0.39 x L/1000 ) μm at k=2 where L is measured Length in mm |
III |
On-site services according to ISO 10360-7: 2011 and FSTM-8 |
Length Measurement Error: EUZ | (0.27 + 0.60 x L/1000 ) μm at k=2 where L is measured Length in mm |
||
Squareness Error: ESQ | (1.79 + 0.003L) μm at k=2 where L is measured Length in mm |
||
Probing Error: PF2D | 0.13 µm | ||
Probing Error: PFV2D | 0.13 µm | ||
Surface roughness | |||
Ra up to 4.1 μm | |||
Ra | 0.07 μm | II | See note 16 |
Rmax, Ry | 0.29 μm | ||
Ra up to 160 μinches | |||
Ra | 3 μinches | II |
See note 16
|
Rmax, Ry | 11 μinches | ||
Precision Glass Scales | |||
0 mm to 400 mm | (1.4 + 0.011L ) µm, where L is Length in mm | II | See note 19 |
0 inches to 15.7 inches | (55.2 + 11L) μinches, where L is Length in inches | ||
Precision Rulers | |||
0 mm to 400 mm | (4.3 + 0.012L ) µm, where L is Length in mm | II | See note 19 |
0 inches to 15.7 inches | (169 + 12L) μinches, where L is Length in inches | ||
Hardness | |||
Indirect verification of Rockwell hardness testers | |||
HRA | Governed by the uncertainty of the standardized test block used to perform the indirect verification | III | ASTM E18 Standardized Test Blocks per ASTM E18 See notes 4, 7 and 8. On-site calibration available. |
HRB | |||
HRC | |||
HRD | |||
HRE | |||
Indirect verification of Rockwell Superficial hardness testers | |||
HR15T | Governed by the uncertainty of the standardized test block used to perform the indirect verification | III | ASTM E18 Standardized Test Blocks per ASTM E18 See notes 4, 7 and 8. On-site calibration available. |
HR30T | |||
HR15N | |||
HR30N | |||
Indirect verification of Vickers and Knoop micro indentation hardness testers | |||
HV | Governed by the uncertainty of the standardized test block used to perform the indirect verification | III | ASTM E384 Standardized Test Blocks per ASTM E384 See notes 5, 7 and 8. On-site calibration available. |
HK | |||
Indirect verification of Vickers hardness testers | |||
HV | Governed by the uncertainty of the standardized test block used to perform the indirect verification | III | ASTM E92 Standardized Test Blocks per ASTM E92 See notes 6, 7 and 8. On-site calibration available. |
Indirect verification of Rockwell and Vickers portable hardness testers | |||
HRC | Governed by the uncertainty of the standardized test block used to perform the indirect verification | III | ASTM E18 and E92 Standardized Test Blocks per ASTM E18 & E92 See notes 4,6, 7 and 8. On-site calibration available. |
HV |